Planet Networking & Communication WDRT-730 Скачать руководство пользователя страница 62

Страница: 62 / 105

User Manual of WDRT-730

-55-

Figure 5-34

WDRT-730 supports two kinds of WPS methods:

Push-Button Configuration (PBC)

, and

PIN code

The detailed instructions are listed follow:

Object

Description

Push-Button Configuration (PBC)

Click

Start PBC

button to start WPS setup procedure.

WDRT-730 will wait for WPS requests from wireless clients for
2 minutes. The

WLAN

LED on WDRT-730 will be steady on

for 2 minutes when this wireless router is waiting for incoming
WPS request.

PIN Code

Please input the PIN code of the wireless client you wish to
connect, and click

Start PIN

button. The

WLAN

LED on

WDRT-730 will be steady on when this wireless router is
waiting for incoming WPS request.

Config Mode

There are

Registrar

and

Enrollee

modes for the WPS

connection. When

Registrar

mode is enabled, the wireless

clients will follow the router’s wireless settings for WPS
connection. When

Enrolle

mode is enabled, the router will

follow the wireless settings of wireless client for WPS
connection.

Table 5-26

5.2.5 QoS

Quality of Service provides an efficient way for clients on the network to share the bandwidth with a

promised quality of Internet service. Without QoS, all computers and devices on the network will

Содержание WDRT-730










































































































Результаты поиска

Содержание WDRT-730

Отзывы:

Бренды по названию

Популярные бренды

Planet Networking & Communication WDRT-730, Руководство пользователя

Результаты поиска

Содержание WDRT-730

Отзывы:

Бренды по названию

Популярные бренды