Planet Networking & Communication WDRT-730 Скачать руководство пользователя

Страница: 17 / 105

User Manual of WDRT-730

-10-

2.1.3 The Rear Panel

The rear panel provides the physical connectors connected to the power adapter and any other

network devices.

Figure 2-3

shows the rear panel of WDRT-730.

Rear Panel

Figure 2-3

Rear Panel

Interface

Function

Antenna x 2

Fixed Dual-Band 3dBi Omni Dipole Antennas.

Radio ON/OFF

Switch the button to activate or deactivate the wireless function.

Reset the WDRT-730 to the factory default (clear all settings) or activate
WPS function.

Reset/WPS

Press for

more than 10 seconds

to reset the device to factory default.

Press for

less than 5 seconds

once to activate 2.4GHz wireless WPS

function.
Press for

less than 5 seconds twice

to activate 5GHz wireless WPS

function.

WAN

Connect to the Cable/xDSL Modem, or the Ethernet

LAN1-4

Connect to the user’s PC or network devices

Power

Connect to the power adapter provided in the package

Table 2-2

The Interface indication

Содержание WDRT-730










































































































Результаты поиска

Содержание WDRT-730

Отзывы:

Похожие инструкции для WDRT-730

Бренды по названию

Популярные бренды

Planet Networking & Communication WDRT-730, Руководство пользователя

Результаты поиска

Содержание WDRT-730

Отзывы:

Похожие инструкции для WDRT-730

Бренды по названию

Популярные бренды