manualshive.com logo in svg

Pittway Notifier AFP1010, Руководство по устранению неисправностей

Поделиться
Скачать
Pittway Notifier AFP1010 Скачать руководство пользователя страница 42

AM2020/AFP1010 Troubleshooting Guide  50432  Revision A  8/13/97

42

Corrective Action:

1) Remove power from the AM2020/AFP1010, batteries first and then AC.  Wait

one minute.  Reapply power - AC first, then batteries.

2) If the trouble does not clear, call Notifier Technical Support.

This is an indication that the 20-conductor ribbon cable (part number 71046) that
connects the DIB (Plug J4) to the SIB (Plug P4) is either missing or defective.

Corrective Action:

1) Verify that the cable is in place and is plugged in correctly.

2) Remove the cable and check the continuity with a voltmeter.

3) If the trouble does not clear, call Notifier Technical Support.

A NFN communications fault has been detected on the indicated port.  This
trouble may be due to disconnected or faulty media.

Corrective Action:

1) Verify wire/fiber is connected.

2) Use the MET-1 to evaluate the wire.

3) Verify NFN configuration (MIB thresholds, node address and port configura

tion).

4) Cycle power.

5) If the trouble does not clear, call Notifier Technical Support.

A NFN communications fault has been detected on the indicated port.  This
trouble may be due to disconnected or faulty media.

Corrective Action:

1) Verify wire/fiber is connected.

2) Use the MET-1 to evaluate the wire.

3) Verify NFN configuration (MIB thresholds, node address and port configura

tion).

4) Cycle power.

5) If the trouble does not clear, call Notifier Technical Support.

The Upload/Download must be enabled in Partial System Programming.  A TF6
Trouble Code will be produced if the EIA-485 Interface is not communicating at
all with the peripheral device.

Corrective Action:

1) Make sure that the Upload/Download has been enabled in programming.

2) Verify that the wiring between the 485 Interface and the computer is correct.

TF3 DIB to SIB Cable
Bad or Missing.

TF4 Communication Link
Failure in Port A.

TF5 Communication Link
Failure in Port B.

TF6 Upload/Download
Communications Fault.

www.PDF-Zoo.com

firealarmresources.com

Содержание Notifier AFP1010

















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды