manualshive.com logo in svg

Pittway ID1002/16, Руководство по эксплуатации

Поделиться
Скачать
Pittway ID1002/16 Скачать руководство пользователя страница 36

997-340-001, Issue 8
April 1998

ID1000 Series Operating Manual

APPENDIX 1

AVAILABLE LOOP DEVICE TYPES

There are six types of analogue sensors:

VIEW (Laser-based Smoke):

Type LPX-751

OMNI (Combined Heat/smoke):

Type IPX-751

IONISATION SMOKE:

Type CPX-551/CPX-751

OPTICAL (PHOTOELECTRONIC) SMOKE:

Type SDX-551/SDX-751

HEAT (THERMAL) Grade 2

Type FDX-551

HEAT (THERMAL) Grade 1

Type FDX-551R

and ten types of module:

Manual Call Point (MCP)

Type M500KACGB

ZONE INTERFACE

Type ZMX-1

LASER BASED ASPIRATING DETECTOR & INTERFACE

LaserStar

MONITOR:(input only)

Type MMX-1

MINI-MONITOR:(input only)

Type MMX-101

MICRO-MONITOR:(input only)

Type M503ME

CONTROL:(input/output)

Type CMX-2

10-WAY MONITOR CARD

Type MMX-10

10-WAY CONTROL RELAY CARD

Type CMX-10R

Loop-powered Sounder

Type AB**, AN**

Note: The ZMX-1 is a lower cost alternative to the Conventional Detector Interface (CDI). However,

the two devices are not interchangeable unless a configuration change is made in the panel.

These modules may be further designated according to the type of equipment which they are
supervising. Possible types are, for input (MMX types):

MCP

Manual call point

MON

General monitoring function

SPRK

Sprinkler switch monitoring

AUX

Auxiliary non-latching input

For output (CMX types):

CTRL

General control output

BELL

Bell, loop-powered sounder or other sounder

CDI

Conventional Detector Interface.

Note 1: In ID1000 Series systems fitted with earlier versions of software, up to 2.14, 1.12, 3.12, the

type CONV was also possible with MMX modules.  This facility is incompatible with
NOTIFIER Limited’s Conventional Detector Interface (CDI) and has now been withdrawn.

Note 2: For newer versions of software (i.e. 3.30 and 1.30, or later) the new device type CONV is

now re-named as device type CDI; this is to distinguish it from the new device type ZMX.

Note 3: Device type HAL has been withdrawn.

Isolators

In addition there is a non-addressable isolator module (type ISO-X) which has the capability to isolate
sections of the loop in the event of short-circuit.

Relays

The panel also has four general purpose relays for the purpose of switching auxiliary equipment,
three of which are designated FIRE, FAULT and EVACUATE transfer, the fourth being SPARE and
programmable, plus two 1-amp programmable, monitored sounder circuits.

32

Содержание ID1002/16








































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды