Pit Boss 72700S, Инструкция и рецепты

Страница: 5 / 32

ENGLISH
ENGLISH
9 8
3. INSTALLING THE CART TO THE BARREL
Parts Required:
1 x Main Barrel (#6)
16 x Screw
(#A)
16 x Locking Washer (#C)
16 x Washer
(#B)
Installation:
• Place a piece of cardboard on the floor to prevent scratching the unit.
Lay the main barrel on its side, hopper end pointed upward, on the
cardboard. Note illustration 3A.
• Insert the assembled cart into the main barrel brace, and secure each leg
to the main barrel brace using four washers, locking washers, and screws.
Repeat same installation for other three support legs, leaving the bottom
side (facing the ground) unsecure. Note illustration 3B.
IMPORTANT: Lock caster wheels before lifting grill upright.
• Carefully, lift the grill into an upright position with the wheels on the
bottom. Secure the final side of the grill using four washers, locking
washers, and screws.
4. ATTACHING THE BOTTLE OPENER
Parts Required:
1 x Bottle Opener (#9)
Installation:
• Secure the bottle opener to the front of the grill using the two pre-
installed screws on the front support leg.
5. SECURING THE LID STOPPER
Parts Required:
1 x Lid Stopper (#3)
Installation:
• Secure the lid stopper onto the top of the main barrel using the pre-
installed screw on the top of the main barrel.
6. ATTACHING THE LID HANDLE
Parts Required:
1 x Lid Handle (#8)
2 x Lid Handle Bezel
(#7)
Installation:
• Remove the pre-installed screws from the lid handle. From inside the
barrel lid, insert one screw so that it protrudes to the outside. Add a
bezel on the screw, then hand-tighten the screw (from the inside) into
the lid handle.
• Repeat same installation for other end of lid handle.
7. ASSEMBLING THE SIDE SHELF
Parts Required:
1 x Side Shelf
(#11)
4 x Tool Hook (#12)
1 x Side Shelf Handle
(#13)
Installation:
• Turn the side shelf upside down. On the edge of the side shelf with four
holes, install the tool hooks into each hole along the edge. Tool hooks
will secure to the self-clinching nut that is pre-mounted on the inside.
• Next, remove the pre-mounted screws from the side shelf handle. On
the edge of the side shelf with two holes, align the handle with the
holes, then hand-tighten the screw (from the inside) into the handle.
Repeat for the other end of the handle.
8. MOUNTING THE SIDE SHELF
Installation:
• Remove the four mounted screws from the side of the main barrel.
• From underneath, secure the side shelf to the side panel of the main
barrel using the four screws previously removed.
NOTE: Do not tighten any screws completely until all screws have
been installed. Once all screws are installed, then tighten securely.
IMPORTANT: Avoid using the side shelves to move or lift the grill.
The weight of the unit will cause the side shelf to break, which is not
covered by warranty.
9. INSTALLING THE GREASE TRAY
Parts Required:
1 x Grease Tray
(#10)
Installation:
• Unscrew the two screws of the pre-mounted handle from the interior
of the grease tray, and reinstall the handle on the exterior.
• Slide the grease tray into the tray opening on the front panel of the
unit. The grease tray is completely inserted once the front of the tray
is flush with the front panel of the unit.
10. INSTALLING THE COOKING COMPONENTS
Parts Required:
2 x Cooking Grids
(#2)
1 x Upper Cooking Rack (#1)
1 x Flame Broiler Main Plate
(#5)
1 x Flame Broiler Slider (#4)
Installation:
• Insert the flame broiler main plate into the main grill. Rest the flame
broiler main plate on the built-in ledge (on the inside right) of the
main grill that directs grease towards the grease bucket. Slide the
entire piece to the left side, and the two slots on the flame broiler
6
4
A C B
3B
5
3A 7
8
9
10A