background image

 

11 

FINAL DETAILS 

 

- The warning sticker must be placed on a visible area, for example, next to the ladder, fig. 32, 33.  
- Place the cap (BU) to the ends of the screws at the bottom of the profiles, fig. 34. (ref. 4906 / ref. 4907 mod. 550 
Ø). 
 
 

 

 

 

 

 

 

 
-  Attach  the  ladder  according  to  the  assembly  instructions,  put it  in  a  place  intended  for  entry  and  exit  from  the 
pool and if possible visible. Remove the ladder after use.  
 
- Assemble the filtration  unit following the instructions. The filtration equipment must be  separated from the pool 
by at least 3.5 meters once it has been connected to the pool by hoses. 

 

INSTALLING THE RETURN VALVE (VR) 

 

The return valve is an element which brings back the filtered 
water  from  the  filter  system,  fig.  35.  Important:  Place 
Teflon®  on  all  threads.  Teflon®  excess  may  break  the 
components. Remove the rear fitting of the return valve and 
place Teflon®, screw all the way. 
 
1) Once the water is at +/- 10 cm. below the lower edge of 
the valve, mark the hole in the liner with a felt pen and with 
a sharp blade, cut the liner carefully into a cross-shape from 
the  inner  wall  of  the  pool  towards  the  outer  wall,  without 
going past the punched hole.  
 
2) On the return valve (A), once the seals are placed, the rubber (B)  is introduced into this pre-cut hole, from the 
interior wall to the exterior wall. Cut the piece of liner that hangs on the external side.  
 
3)  Place  the  rubber  washer  (C)  on  the  outer  wall,  put  Teflon®  on  the  threads  and 
tighten firmly  with the  large nut (D)  inserting Teflon®  and the return  hose (E),  which 
runs from the filter system to  the return valve (a) and secure it with a clamp (H). 
 
 

For better filtering we advise you to direct the water. In order to do this, you will 

have  to  loosen  the  washer  (AR),  move  the  swivel  ball  (BO)  slightly  upwards  to  one 
side  of  the  pool  and  tighten  the  washer  (AR).  In  this  way  impurities  will  be  directed 
towards the skimmer. 

 

INSTALLING THE SKIMMER (SK) 

 

Keep  on  filling  the  swimming  pool  with  water  up  to  5  cm  below  the 

skimmer  hole.  With  a  felt  pen  mark  on  the  liner  the  square  hole  for  the 
installation  of  the  skimmer  and  cut  the  piece  of  liner  marked  with  a  sharp 
blade.  
 

Place the  double rubber  washer (Z) on the steel  wall. The steel  wall  and 

liner must go inside the grooves of the washer. Next, install the skimmer frame 
with  the  screws.  Make  sure  that  all  the  holes  are  lined  up  (washer,  hole  and 
skimmer).  Fix  the  holes  with  the  screws  one  after  the  other  until  a  perfect 
match is made, but do not tighten them up too much. Start fastening and finally 
tighten the screws firmly following the same order. 
 

Cover the frame (M) threading with Teflon® and fasten it up firmly into the 

skimmer.  Fix  one  hose  end  to  the  frame  (M)  with  a  clamp  (H).  Connect  the 
other hose end to the filter water inlet and tighten with a clamp. 
 

 

     

fig. 35                                                           

Содержание Canarias Series

















Отзывы: