WARNING! This device is not intended for use with
emergency exit fixtures or emergency exit lights.
WARNING! Permanent damage to the low voltage 12VAC
lamp will occur if installed on a 120VAC circuit.
ATTENTION 12V PUREWHITE OWNERS!
DANGER!
Risk of electrical shock or electrocution
WARNING!
Read this before attempting installation
Rated Lamp Life
Safety Precautions
IMPORTANT NOTE:
Installation
PureWhite
TM
Pool & Spa Lamp Installation and Operation Guide
PUREWHITE REPLACEMENT LED IN-GROUND POOL & SPA LAMPS
Model #s: LPL-P2-WHT-12, LPL-P2-WHT-120, LPL-M1-WHT-12, LPL-M1-WHT-120, LPL-PR-WHT-120, LPL-PR-WHT-12
Compatible NRTL light housings
include:
Hayward
®
Astrolite
™
SP058 & SP059 Series
Hayward
®
Astrolite
™
SP058 & SP059 Series Housing -
Use replacement gasket specified by manufacturer.
Sta-Rite
®
SwimQuip
™
Series 0508
Sta-Rite
®
SwimQuip
™
Series 0508
-
Requires installation with included
J&J Gasket.
Jacuzzi
®
Full Moon
™
Jacuzzi
®
Full Moon
™
-
Use replacement gasket specified by manufacturer.
Pentair
®
Amerlite 784 Series
Pentair
®
Amerlite 784 Series & SpaBrite
™
Series
-
Requires installation
with included J&J Gasket.
Gasket compatibility
™
The product warranty is voided if the proper gasket is not installed.
See the “Warranty” section at the end of this manual for details.
STEP 1
Remove light housing from niche
Figure 1: LPL-P2-WHT
PAGE 1
STEP 2
Remove old lamp
PureWhite Replacement LED In-Ground Pool and spa lamps are
available in 12VAC (low voltage) and 120VAC models as indicated
on the product packaging. Each lamp has a screw-in Edison base.
A socket voltage range of 12.0 –15.0 will achieve optimal brightness. To
verify the voltage, at the lamp socket, measure the open circuit voltage
(no lamp in the socket).
Your PureWhite lamp is not an ordinary light bulb. It is a valuable
electronic device that is not designed to come in direct contact with
water. An improper installation that results in water leakage into the pool
light housing can permanently damage the PureWhite lamp.
Please read
these installation steps and the original manufacturer’s pool light
installation manual carefully before proceeding.
Make sure power to the pool light is turned off at the circuit breaker.
Carefully remove the existing light housing from the niche assembly and
place it on the pool deck. There should be enough power cord to do this
easily. If there is not enough power cord to allow the light housing to
reach the pool deck surface, call your local pool service company.
Access the old lamp according to the original manufacturer’s pool light
installation manual. Remove the screws and/or loosen the clamp that
holds the face plate and lens in place. Carefully remove the lens from the
pool light housing. Take care not to damage the surface of the light
housing body that makes contact with the rubber gasket.
WARNING! Verify that your PureWhite lamp voltage
rating (120VAC or 12VAC) matches your electrical
system’s voltage requirements before proceeding
with installation.
The illumination generated by the PureWhite Replacement LED
In-Ground Pool lamp is based on Light Emitting Diode (LED) technolo-
gy. The average expected lamp life is rated up to 50,000 elapsed time
hours under normal operating conditions. [Temperature: 33°F to 95°F
(1°C to 35°C), Humidity: 0-95% non-condensing].
•
Do not open, service or tamper with any internal component of the
PureWhite Replacement LED In-Ground Pool lamp. Doing so will
void the warranty. Follow each instruction in this owner’s manual
and pay careful attention to all warnings.
•
Do not directly expose or immerse the PureWhite Replacement
LED In-Ground Pool lamp in water without containing it in a
proper, watertight, NRTL (nationally recognized testing laboratory)
pool light housing and niche assembly.
•
Handle the PureWhite Replacement LED In-Ground Pool lamp with
care. Be careful not to drop the unit.
PureWhite lamps are recommended for installation by a qualified pool
professional.
The installation steps in this owner’s manual are intended as guidelines.
For specific instructions on how to replace a pool lamp, please refer to
the original manufacturer’s pool light installation manual before
proceeding.
PureWhite Replacement LED In-Ground pool and spa lamps must be
installed in a compatible NRTL pool light housing.
•
Keep the pool light housing dry.
Always disconnect power to the pool light at the circuit breaker panel
before attempting to service the lamp. Failure to do so could result in
serious injury or death due to electrical shock. Refer to the original
manufacturer’s pool light installation manual before proceeding. As with
any electrical device, installation and service should always be
performed by a qualified
individual.
This device is not intended for use
in anything other than in-ground pools.
PureWhite Replacement LED In-Ground Pool and spa lamps offer superior, bright white illumination for your pool. This owner’s manual
contains important information on installing and using your new PureWhite Replacement LED In-Ground Pool or Spa lamp. Please read it
carefully and keep it in a safe place for future reference.
6 Bendix, Irvine, CA 92618 USA
•
800.735.4553
•
949.455.4460
•
www.jandjpoolspa.com
