Pioneer VSX-C402 страница 45 Скачать руководство пользователя

Страница: 45 / 46

Additional information

English

SCART pin assignment

• Specifications and the design are subject to possible

modifications without notice, due to improvements.

Pin

DVD & STB

VIDEO

DVR/TV

N.C.

Audio right output Audio right output

Audio right input

N.C.

Audio left output

Common GND for
audio

GND for (7)

Audio left input

Blue input

Blue output

Status & aspect
input

Status & aspect
output

GND for (11)

N.C.

i/o-Link.A control

Green input

Green output

N.C.

GND for (15)

GND for (16)

Red/S-video(C)
input

Red/S-video(C)
output

Blanking input

Blanking output

GND

GND for (19)

GND for (20)

N.C.

Video output

Video/S-video(Y)
output

Video/S-video(Y)
input

Video input

GND (plug shield)

GND (plug shield) GND (plug shield)

vsx-c402_MY.book 45 ページ２００４年２月６日　金曜日　午後７時１９分

Содержание VSX-C402















































Результаты поиска

Содержание VSX-C402

Отзывы:

Похожие инструкции для VSX-C402

Бренды по названию

Популярные бренды

Pioneer VSX-C402, Инструкция по эксплуатации

Результаты поиска

Содержание VSX-C402

Отзывы:

Похожие инструкции для VSX-C402

Бренды по названию

Популярные бренды