Pioneer VSX-AX4AVi-S Скачать руководство пользователя страница 51

Страница: 51 / 88

Other connections

Connecting the multichannel analog inputs

For DVD Audio and SACD playback, your DVD player may
have 5.1, 6.1 or 7.1 channel analog outputs (depending
on whether your player supports surround back

channels).

Make sure that the player is set to output

multichannel analog audio.

Connect the front, surround, center and subwoofer

outputs on your DVD player to the corresponding
MULTI CH input jack on this receiver.

• Use standard RCA/phono jack cables for the

connections.

If your DVD player also has outputs for surround

back channels, connect these to the corresponding
MULTI CH input jacks on this receiver.

• Use standard RCA/phono jack cables for the

connections.

• If there is a single surround back output, connect it to

the

SURROUND BACK L (Single)

jack on this

receiver.

Selecting the multichannel analog inputs

If you have connected a decoder or a DVD player as
above, you must select the analog multichannel inputs

for surround sound playback.

Make sure you have set the playback source to the

proper output setting.

For example, you might need to set your DVD player to
output multichannel analog audio.

Use the INPUT SELECT button to select MULTI CH IN.

You can also use the

INPUT SELECTOR

dial on the front

panel.

• Depending on the DVD player you’re using, the

analog output level of the subwoofer channel may be
too low. In this case switch the receiver into standby,
then press

STANDBY/ON

while holding down

VIDEO SELECT

on the front panel. This switches

between

SW IN +10dB

(increase of 10 decibels) and

SW IN 0dB

(default) in the subwoofer channel.

Using the USB interface

VSX-AX4AVi only

It is possible to listen to two channels of audio from your
computer by connecting to the USB interface on the rear
of this receiver. Depending on your model of computer
and the software installed, you can listen to the stereo
audio source through the speaker setup you’ve

connected to this receiver.

Connect your computer’s USB terminal to the USB

terminal on the rear panel of this receiver.

Switch on your computer and this receiver.

Note

1 To listen to multichannel analog audio you’ll need to switch the input signal selector to

MULTI CH INPUT

(see

Selecting the multichannel analog inputs

above for more on this).
2 • When playback from the multichannel inputs is selected, you can’t use Midnight/Loudness, Dialog Enhancement or the

SIGNAL SELECT

and

ANA-

LOG ATT

buttons, as well as any of the listening modes (including

STEREO

and the surround back channel processing).

• When playback from the multichannel inputs is selected, only the volume and channel levels can be set.
• You can’t listen to your speaker B (Second Zone) system during playback from the multichannel inputs.

RECEIVER

SOURCE

SYSTEM OFF

INPUT

SELECT

DVD

SAT

VIDEO 1

TV CONT

VIDEO 2

3 • Windows

XP, Windows

2000, Windows

Millennium Edition and Windows

98 Second Edition operating systems have been tested for compatibility

with this interface, but depending on your computer setup, you may find that your system is not compatible.

• Make sure you use a USB cable that connects from an A-type connector (from your PC) to a 4-pin B-type connector (to the receiver).
• The USB specification is version 1.1 compatible, and the USB Audio Class specification is 1.0 compatible.
• Any computer alert sounds will also be heard through the speakers unless you switch them off from the computer’s control panel.
• You won’t be able to hear the audio from the USB connection through the digital outputs of this receiver.
• Note that using hubs or extensions may cause connection problems.

S400

(AUDIO)

S400

MULTI-ROOM

&SOURCE

/REC SEL

OUT1

ROOM3(ZONE3)

OUT2

USB
AUDIO
IN

(SAT)

(DVR/
VCR 1)