Additional information
12
78
En
i.LINK messages
You may see the following messages displayed in the front panel display when using the i.LINK interface.
USB interface
HDMI
You can’t get i.LINK to display
when using the
SIGNAL SELECT
button.
• Make sure your i.LINK source components are switched on.
• Check that i.LINK is assigned correctly (see
The Input Setup menu
on page 60).
After upgrading a component, it
is not recognized and cannot be
selected using the i.LINK
connection.
• You may need to reset the i.LINK database memory in the receiver (use the front panel):
With the receiver in standby, press
STANDBY/ON
while holding down
RETURN
. When you see
DB
CLEAR?
appear in the display, press
ENTER
, then
SETUP
again to confirm. When you’ve reset the i.LINK
database memory,
DB CLEAR SET
shows in the display. If
DB ERROR
is displayed, step through the
procedure again.
Message
Explanation
BUS FULL
The i.LINK bus has reached its capacity and cannot transmit any more data.
CANNOT LINK 1
The connection between the receiver and the selected i.LINK-equipped component is unstable. If the
i.LINK cables appear to be connected properly and both the receiver and i.LINK-equipped component are
on, switch both units off, then on again to re-establish the connection between them.
CANNOT LINK 2
The receiver can’t identify the selected i.LINK-equipped component. For example, the receiver may not be
able to identify an i.LINK-equipped personal computer.
LINK CHECK
The receiver is checking the i.LINK network. It does this when components are added to, or removed from
the network. The sound may be interrupted if this happens during playback.
LOOP CONNECT
The i.LINK network cannot function because the connected components form a loop. See
Creating an
i.LINK network
on page 50 for more on this.
NO NAME
When an i.LINK-equipped component has no name, this message is displayed instead of the proper
component name.
NO SIGNAL
A component is outputting an i.LINK signal that the receiver cannot reproduce. This receiver can only
reproduce signals from i.LINK-Audio-equipped components. See
About i.LINK
on page 49 for more on this.
PQLS OFF
This is displayed on a playback component when PQLS turns off during playback. The sound may be
interrupted momentarily when this happens.
PQLS ON
This is displayed on a playback component when PQLS turns on during playback. The sound may be
interrupted momentarily when this happens.
UNKNOWN
When an i.LINK-equipped component name cannot be recognized, this message is displayed instead of
the proper component name.
Symptom
Remedy
Symptom
Remedy
No sound.
• Make sure you have set up your computer system to output through the USB interface (see
Using the USB
interface
on page 51).
• Make sure your computers output level is turned up.
• Update to a more recent version of your software, try a different audio program, or try a different source.
Symptom
Remedy
The HDMI indicator blinks
continuously.
• Check all the points below.
No picture or sound.
• This receiver is HDCP-compatible. Check that the components you are connecting are also HDCP-
compatible. If they are not, please connect them using the component, S-video or composite video jacks.
• Depending on the connected source component, it’s possible that it will not work with this receiver (even
if it is HDCP-compatible). In this case, connect using the component, S-video or composit video jacks
between source and receiver.
• If the problem still persists when connecting your HDMI component directly to your monitor, please
consult the component or monitor manual or contact the manufacturer for support.
12_additional_info.fm 78 ページ ２００５年９月２０日 火曜日 午前１１時５６分
Содержание VSX-AX4AVi-S
Страница 87: ...Additional information 12 87 En ...
