Pioneer KURO KRP-500P, Руководство по обслуживанию

Страница: 17 / 161

17
KRP-500P
5 6 7 8
5 6 7 8
A
B
C
D
E
F
Structure of Layers in Service Factory Mode
I N FORMATIO N mode
1. V ERSIO N (1) The software versions for each microcomputer
2. V ERSIO N (2) The Flash memory versions for each device
3. V ERSIO N (3) The software versions for display microcomputer
4. MAI N N G The shutdown message ID/event times
(Going Clear mode by [E N TER/SET] key)
4-1. CLEAR Select Yes by [
l
] key
l
pushing and hold [E N TER/SET] key
5. TEMPERATURE The temperature/FA N rotating status
6. HOUR METER The HOUR METER/P-COU N T information
7. HDMI SIG N AL I N FO 1 The information of HDMI information files
8. HDMI SIG N AL I N FO 2 The information of HDMI information files
9. V DEC SIG N AL I N FO 1 The signal information of V DEC
10. V DEC SIG N AL I N FO 2 The signal information of V DEC
PA N EL FACTORY mode Refer to [PA N EL FACTORY MODE]
PA N EL MAI N FACTORY mode
1. PM N G I N FO. Shutdown history of the panel main
2. PM STATE I N FO. The temperature/FA N rotating status/Room Light Sensor
3. DP_RX I N FO. Indication of the DPRx ID
4. PM_SETUP Select the bezel color and clear the shutdown history of
the panel main
OPTIO N mode
1. CH PRESET For production line use
2. Digital AFT For production line use
3. SY N C DET For technical analysis
4. CTI For technical analysis
I N ITIALIZE mode
1. SIDE MASK LE V EL For factory use
1-1. SIDE MASK LE V EL
2. FI N AL SETUP Set to Factory default settings (it should perform after
2-1. DATA RESET replacing a MAI N Assy)
3. DTB SER V ICE MODE Information for the Digital Tuner Service Menu is displayed
3-1. MODE SHIFT
4. W ide XGA AUTO For technical analysis
5. AUTO ADJUSTME N T
Quick Reference upon Service Visit
2
Mode transition and structure of layers in Service Factory mode
I N FORMATIO N mode
1. V ERSIO N (1)
2. V ERSIO N (2)
3. V ERSIO N (3)
4. MAI N N G
5. TEMPERATURE
6. HOUR METER
7. HDMI SIG
N AL I N FO 1
8. HDMI SIG N AL I N FO 2
9. V DEC SIG N AL I N FO 1
10. V DEC SIG N AL I N FO 2
PA N EL FACTORY mode
1. PA N EL I N FORMATIO N
2. PA N EL W ORKS
3. PO W ER DO WN
4. SHUT DO WN
5. PA N EL-1 ADJ
6. PA N EL-2 ADJ
7. PA N EL FU N CTIO N
8. ETC.
9. RASTER MASK SETUP
10. PATTE
N MASK SETUP
11. COMBI MASK SETUP
I N ITIALIZE mode
1. SIDE MASK LE V EL
2. FI N AL SETUP
3. DTB SER V ICE ME N U
4. W ide XGA AUTO
5. AUTO ADJUSTME N T
OPTIO N mode
1. CH PRESET
2. Digital AFT
3. SY
N C DET
4. CTI
• To shift to another mode, press [MUTI N G].
• To shift to another item in a specific mode,
press
[
i
] or [
j
].
• To shift to the next nested layer below for an
item with a "(+)" indication, press [E
N TER/SET].
To return to the next nested layer above,
also press [E
N TER/SET].
Mode transition in Service Factory mode
Up
Down
Structure of Layers in Panel Factory Mode 2
8. ETC (+)
1. BACKUP DATA
2. DIGITAL EEPROM
3. PD I N FO.
4. SD I N FO.
5. HR-MTR I N FO.
6. PM/B1-B5
7. P COU N T I N FO.
8. MAX TEMP.
9. MIRROR
10. CLS
9. RASTER MASK SETUP (+)
1. MASK OFF
2. RST MASK 01
• • • • •
10. PATTER N MASK SETUP (+)
1. MASK OFF
2. PT N MASK 01
• • • • •
11. COMBI MASK SETUP (+)
1. MASK OFF
2. CMB MASK 01
• • • • •
Structure of Layers in Panel Factory Mode 1
1. PA
N EL I N FORMATIO N V ersion indication of the panel
2. PA N EL W ORKS Indications of the accumulated power-on time and
power-on count of the panel
3. PO W ER DO WN Indication of the Power-down history
4. SHUT DO WN Indication of the Shutdown history
5. PA N EL-1 ADJ (+)
1. V OL SUS
2. V OL OFFSET
• • • • •
10. RESET1ST_KSB
• • • • •
25. SUS FREQ
6. PA N EL-2 ADJ (+)
1. R-HIGH
2. G-HIGH
• • • • •
6. B-LO W
7. ABL
7. PA
N EL FU N CTIO N (+)
1. R-LE V EL
• • • • •
To "Structure of Layers in Panel Factory Mode 2"
For AM noise prevention (Depending on the mode,
brightness of the screen changes.)
For confirmation of the result of the setting change,
the unit must be turned off then back on again.
Items for factory use
Items for factory use
Settings required after replacement of the panel
For transferring backup data (after replacement of
the DIGITAL Assy)
Change the adjustment status of the DIGITAL Assy.
For use while the Raster Mask is displayed.
Use [
i
] or [
j
] to select the type of mask.
Use [
l
] or [
k
] to select the sequence.
Switch the Mirror display mode.
Switch the function when checking the color sensor
level.
For use while the Pattern Mask is displayed.
Use [
i
] or [
j
] to select the type of mask.
Use [
l
] or [
k
] to select the sequence.
For use while the Combination Mask is displayed.
Use [
i
] or [
j
] to select the type of mask.
Use [
l
] or [
k
] to select the sequence.
For clearance of data for the corresponding items.
The clearing method is the same: Select "CLEAR",
then hold [E
N TER/SET] pressed for at least 5
seconds.
For the W B adjustment of the panel and ABL
adjustment.
A setting table is available for each signal frequency.
PA N EL MAI N FACTORY mode
1. PM N G I N FO
2. PM STATE I N FO.
3. DP_RX I N FO.
4. PM_SETUP