background image

 
 

User manual RXN-406 Keypad for CAPTAIN-i Alarm System

 

2

 

 

 
 

PIMA Electronic Systems Ltd. does not represent that its Product may not be 
compromised and/or circumvented, or that the Product will prevent any death, personal 
and/or bodily injury and/or damage to property resulting from burglary, robbery, fire or 
otherwise, or that the Product will in all cases provide adequate warning or protection.  
The User understands that a properly installed and maintained equipment may only 
reduce the risk of events such as burglary, robbery, and fire without warning, but it is not 
insurance or a guarantee that such will not occur or that there will be no death, personal 
damage and/or damage to property as a result. 

PIMA Electronic Systems Ltd. shall have no liability for any death, personal and/or 
bodily injury and/or damage to property or other loss whether direct, indirect, 
incidental, consequential or otherwise, based on a claim that the Product failed to 
function. 

Warning: 

The user should follow the installation and operation instructions and among 

other things test the Product and the whole system at least once a week.  For various 
reasons, including, but not limited to, changes in environment conditions, electric or 
electronic disruptions and tampering, the Product may not perform as expected.  The 
user is advised to take all necessary precautions for his/her safety and the protection of 
his/her property. 

This document may not be duplicated, circulated, altered, modified, translated, reduced 
to any form or otherwise changed, unless PIMA’s prior written consent is granted. 

All efforts have been made to ensure that the content of this manual is accurate.  Pima 
retains the right to modify this manual or any part thereof, from time to time, without 
serving any prior notice of such modification. 

Please read this manual in its entirety before attempting to program or operate your 
system.  Should you misunderstand any part of this manual, please contact the supplier 
or installer of this system. 

Copyright 

 2005 by PIMA Electronic Systems Ltd.  All rights reserved. 

You can contact us at: 
PIMA Electronic Systems Ltd. 
5 Hatzoref Street, Holon 58856, Israel  http://www.pima-alarms.com 

 

 

 

 

 

 

Содержание RX-406
















Отзывы: