Pilz PMCtendo SZ Series Скачать руководство пользователя страница 38

Страница: 38 / 88

Commissioning

Operating Manual PMCtendo SZ
1002405-EN-04

7.1

Checking the motor installation

DANGER!

Burns!
The surface temperature of a synchronous servo motor can significantly ex-
ceed 65 °C through operation.

– Take suitable protective measures against unintentional and inten-

tional contact with the motor.

You have installed a synchronous servo motor as described in the chapter

Installation [

17]

Check the general installation and alignment of the synchronous servo motor.

Check the drive elements (coupling, gear unit, belt drive) for firm placement and correct
setting.

Check whether the motor surface is protected against unintentional or intentional con-
tact.

Check whether measures have been taken to prevent possible contact with tempera-
ture-sensitive motor parts.

Check whether the rotor of the synchronous servo motor can turn freely.

If a motor brake is present, it must be released before inspection. Also note the polarity
of the connections!

Содержание PMCtendo SZ Series

























































































Результаты поиска

Содержание PMCtendo SZ Series

Отзывы:

Похожие инструкции для PMCtendo SZ Series

Бренды по названию

Популярные бренды

Pilz PMCtendo SZ Series, Руководство по эксплуатации

Результаты поиска

Содержание PMCtendo SZ Series

Отзывы:

Похожие инструкции для PMCtendo SZ Series

Бренды по названию

Популярные бренды