Pilz PMCprimo Drive2 Скачать руководство пользователя

Страница: 5 / 100

2 Table of contents

Page

Installation manual PMCprimo Drive2

8.2

Assembly................................................................................................................. 33

8.3

Dimensions.............................................................................................................. 34

8.4

Wiring ...................................................................................................................... 35

8.4.1

Connection diagram PMCprimo Drive2 - part 1................................................ 37

8.4.2

Connection diagram PMCprimo Drive2- part 2................................................. 38

8.4.3

Pin assignments overview ................................................................................ 39

8.4.4

Pin assignments - details.................................................................................. 40

8.4.5

Pin assignments Modbus/Profibus ................................................................... 41

8.4.6

Notes on connection techniques....................................................................... 42

8.5

Key operation for parameter setting ........................................................................ 43

8.5.1

Comparison to the key operation with PMCtendo DD4 .................................... 43

8.5.2

Basic key operation .......................................................................................... 43

8.5.3

Menu operation................................................................................................. 43

8.5.4

LED Display...................................................................................................... 44

8.5.5

Automatic detection in PMCprimo .................................................................... 44

Interfaces........................................................................................................... 45

9.1

Power supply ........................................................................................................... 45

9.1.1

Mains supply (X0)............................................................................................. 45

9.1.2

24V-auxiliary supply (X4).................................................................................. 46

9.1.3

24V-Supply (X10) ............................................................................................. 47

9.1.4

Master encoder supply (X10) .......................................................................... 48

9.1.5

DC-link (X7)...................................................................................................... 49

9.2

Motor connection with brake (X9) ............................................................................ 49

9.2.1

Lead length < 25m............................................................................................ 49

9.2.2

Lead length > 25m............................................................................................ 50

9.3

External regen resistor (X8)..................................................................................... 51

9.4

Feedback................................................................................................................. 52

9.4.1

Resolver connection (X2) ................................................................................. 52

9.4.2

HIPERFACE Encoder (X1)............................................................................... 53

9.5

Encoder emulations................................................................................................. 54

9.5.1

Incremental encoder emulation ROD (X5)........................................................ 54

9.5.2

Application example ......................................................................................... 54

9.5.3

SSI emulation (X5) ........................................................................................... 55

9.5.4

Application example ......................................................................................... 55

9.6

RS232 interface, PC interface (X6) ......................................................................... 56

9.6.1

General............................................................................................................. 56

9.6.2

Pin assignment of the null-modem cable.......................................................... 57

9.7

Digital signals .......................................................................................................... 59

9.7.1

Digital inputs I1:1 - I1:8 (X10) ........................................................................... 59

9.7.2

Digital inputs I2:1 - I2:4 (X3) ............................................................................. 60

9.7.3

Digital ENABLE input (X3)................................................................................ 61

9.7.4

Digital outputs O1:1 - O1:8 (X10) .................................................................... 62

9.7.5

Digital outputs Digital-Out 1+2 (X3) .................................................................. 63

9.7.6

Relay output (X3).............................................................................................. 64

9.8

Analog signals ......................................................................................................... 65

9.8.1

Analog outputs AO2 and AO3 (X3)................................................................... 65

9.8.2

Analog inputs AI1 and AI2 (X3) ........................................................................ 66

9.9

CAN bus interface (X11/2 and X11/1) ..................................................................... 67

9.9.1

General............................................................................................................. 67

9.9.2

Connecting PMCprimo Drive2 systems ............................................................ 67

9.9.3

CAN bus cable.................................................................................................. 68

9.9.4

Speciality 1

node ........................................................................................... 68

9.9.5

Speciality last node........................................................................................... 68

9.9.6

Fault detection.................................................................................................. 68

9.9.7

Connecting external CANopen bus devices ..................................................... 68

9.10

Master encoder interface / CAN2 (X11/4) ............................................................... 69

9.10.1

CAN 2 interface .............................................................................................. 70

9.10.2

Jumper settings .............................................................................................. 71

9.10.3

Incremental encoder....................................................................................... 72

9.10.4

Absolute encoder (SSI) .................................................................................. 73

9.11

Bus interface (X11/3) .............................................................................................. 74

9.11.1

General........................................................................................................... 74

9.11.2

MODBUS Interface......................................................................................... 74

9.11.3

Profibus interface (Option).............................................................................. 75

9.11.4

Using the MODBUS / Profibus interface with PMCprimo................................ 75

9.11.5

Example: Profibus DP slave module .............................................................. 75

9.12

Virtual inputs and outputs........................................................................................ 77

9.12.1

Terms ............................................................................................................. 77

9.12.2

Application example ....................................................................................... 77

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Содержание PMCprimo Drive2





































































































Результаты поиска

Содержание PMCprimo Drive2

Отзывы:

Похожие инструкции для PMCprimo Drive2

Бренды по названию

Популярные бренды

Pilz PMCprimo Drive2, Руководство по установке

Результаты поиска

Содержание PMCprimo Drive2

Отзывы:

Похожие инструкции для PMCprimo Drive2

Бренды по названию

Популярные бренды