SERIES INTERRUPTED
SERIES X/12
After interrupting the series, you can measure the last cut
piece. If its length differs from the required one, you can set the
correction. This correction will be counted immediately after
restoring the series by pressing the CONTINUE button.
Upon pressing the button, the series performance will be
ended and you will be directed back to the default screen of
the automatic mode.
End of the interrupted series
By pressing the button, the cutting cycle is restored -
return to the screen PERFORMING SERIES.
Continue with the interrupted
series
CONTINUE
AaBbCcDdE
1
SERIES
357
LENGTH
10
PIECES
225
HEIGHT
By pressing the icon, the screen
Notes on the series will appear on the display.
Adjust the length of the workpiece from 1 mm
to 9999 mm, with the accuracy of 0.1 mm.
Set the number of pieces to cut in one series
Setting Band Saw Arm Ascent Height
Do not fill in value which is lesser than 40 mm.
FEED Return feed
- the default position of
the movable vice is 0 mm. From this value, the
vice will move to the distance set for the
particular series. The material gets clamped
and the vice returns to the zero position. The
cut will be performed. During the cut, the
material is clamped only by the fixed vice. The
movable vice travels during the cut for a next
feed. Suitable for cutting long, light pieces.
FEED
ACT.
LIST
ESC
Gradual feed
- the default position of the
movable vice is 500 mm. Using this value, the
vice will clamp the material and will keep
holding it while feeding the material by the set
value. After finishing the cut, the vice will feed
the material by the set value. If it is no longer
possible to feed the material towards 0 mm,
the vice move again to 500 mm. If the material
is shorter, the optical sensor stops the running
gear and vise clamps the material behind the
past about 50 mm and then feeds this residue.
The material is permanently clamped by the
two vices. Suitable for cutting of short or heavy
items.
FEED
Active/inactive series
- The active
series is symbolized by a green tick mark.
Always after the start of series editing, the
series turns of (red cross). After finishing
the editing, it is necessary to turn it on
again. It is possible to have programmed
a greater amount of series and only
switch them on and off as needed.
By pressing the icon, the screen SERIES
LIST will appear on the display.
Leafing through the series
(12 screens)
Pressing this icon takes you back to the
default screen.
ARM UPLIFT HEIGHT H SETTING
Press the icon in order to display a table for
optimal setting of the height of the cut log.
This button represents a part of the system
in the following machines: ARG 260 CF-
NC, ARG 300 CF-NC, ARG 330 CF-NC.
H
SERIES INTERRUPTED
0 9 : 2 0 : 0 3
0 8 / 1 0 / 2 0 1 6
CORRECTION
65
15
90
BLADE SPEED
m/min
1.12
6,5
0%
150%
AMMETER
A
50
100
Total
Finished
SERIES NO.
6
FEED
340
0
0
mm
mm
mm
mm / min
493.0
20.00
SERIES
CONTINUE
TIMES
Latest
pc
min
sec
ACTIVE SERIES
0
00
0
00
Remaining
1
2
5
6
7
8
9
12
14
15
357
10
225
159
15
65
456
65
225
268
98
85
358
75
285
AaBbCcDdE
1
AaBbCcDdE
2
AaBbCcDdE
3
AaBbCcDdE
4
AaBbCcDdE
5
SERIES 1/12
0 9 : 2 0 : 0 3
0 8 / 1 0 / 2 0 1 6
ESC
LIST
SERIES
LENGTH
PIECES
HEIGHT
FEED
ACT.
H
Содержание ARG 260 CF-NC automat
Страница 2: ......
Страница 13: ...J S ARG 520 DC CF NC automat C A D E F G H K L M N O P Q R S T W X...