PIE PIE 830PM Скачать руководство пользователя страница 36

Страница: 36 / 44

Page 34

Practical Instrument Electronics

Tel: 585.872.9350 • Fax: 585.872.2638 • [email protected] • www.piecal.com

Specifications

General

Operating Temp Range

-20 to 60 °C (-5 to 140 °F)

Storage Temp Range

-30 to 60 °C (-22 to 140 °F)

Temperature effect

≤ ± 0.01 %/°C of Full Scale; Cold Junction Sensor ≤ ±25 ppm/°C

Relative Humidity Range

10 % ≤RH ≤90 % (0 to 35 °C), Non-condensing
10 % ≤RH≤ 70 % (35 to 60 °C), Non-condensing

Isolation: Voltage

Common Mode

60V rms between all mA functions/Read V DC and Source V DC/

thermocouple/RTD/Ohms//Frequency/Pressure
50/60 Hz, 100 dB

Normal Mode Rejection

50/60 Hz, 50 dB

Noise

≤ ± ½ Least Significant Digit from 0.1 to 10 Hz

Size

5.63x3.00x1.60” 143x76x41mm (LxWxH)

Weight

12.1 ounces, 0.34 kg with boot & batteries

Batteries

Four “AA” Alkaline 1.5V (LR6)

Battery life

Read Functions: ≥ 20 hrs; Pressure ≥ 7 hrs

Source mA: ≥ 14 hours @ 12 mA into 250Ω

Pwr/Meas mA: ≥ 12 hours at 20 mA

Source V, Ω, T/C, RTD & Hz: ≥ 20 hours

Low Battery

Low battery indication with nominal 1 hour of operation left

Protection against

misconnection

Over-voltage protection to 60 vrms (rated for 30 seconds)

Red LED indicates OVERLOAD or out of range conditions

Display

High contrast graphic liquid crystal display, 0.315” (8.0 mm) high digits,

backlighting

Read mA

Ranges and Resolution

0.000 to 24.000 mA or -25.00 to 125.00% of 4-20 mA

Accuracy

≤ ± (0.02 % of R 0.003 mA)

Voltage burden

≤ 2V at 24 mA

Overload/Current limit

protection

25 mA nominal

Source mA / Power & Measure Two Wire Transmitters

Ranges and Resolution

Same as Read mA

Accuracy

≤ ± (0.02 % of R 0.003 mA)

Loop compliance voltage

≥ 24 DCV @ 20.00mA

Loop drive capability

1200 Ω at 20 mA for 15 hours nominal;

950 Ω with Hart Resistor enabled

mA 2-Wire Transmitter Simulation

Accuracy

Same as Source/Power & Measure

Voltage burden

≤ 2V at 20 mA

Overload/Current limit

24 mA nominal

Loop voltage limits

2 to 60 VDC (fuse-less protected)

Содержание PIE 830PM













































Результаты поиска

Содержание PIE 830PM

Отзывы:

Бренды по названию

Популярные бренды

PIE PIE 830PM, Руководство пользователя

Результаты поиска

Содержание PIE 830PM

Отзывы:

Бренды по названию

Популярные бренды