manualshive.com logo in svg

PIE PIE 830PM, Руководство пользователя

Поделиться
Скачать
PIE PIE 830PM Скачать руководство пользователя страница 35

Page 33

Practical Instrument Electronics

Tel: 585.872.9350 • Fax: 585.872.2638 • [email protected] • www.piecal.com

Warranty

Our equipment is warranted against defective material and workmanship 
(excluding batteries) for a period of three years from the date of shipment. 
Claims under warranty can be made by returning the equipment prepaid to our 
factory. The equipment will be repaired, replaced or adjusted at our option. The 
liability of Practical Instrument Electronics (PIE) is restricted to that given under 
our warranty. No responsibility is accepted for damage, loss or other expense 
incurred through sale or use of our equipment. Under no condition shall Practical 
Instrument Electronics, Inc. be liable for any special, incidental or consequential 
damage.

Accessories

INCLUDED:

AC Adaptor (Part No. 020-0101 for 100 to 120V, 020-0100 for 220/230V ac), Certificate of 
Calibration, Six (6) Mounting Screws

PIE Multifunction Wire Kit 

                      Part No. 020-0820

   1 Red & 1 Black Lead with Banana Plug & Alligator Clips
   2 Red & 2 Black Leads with Banana Plugs & Spade Lugs

OPTIONAL:

T/C Wire Kit 1* for Types J, K, T & E        Part No. 020-0202

T/C Wire Kit 2* for Types B, R/S & N        Part No. 020-0203

* Thermocouple extension wire, stripped on one end with a corresponding miniature 
thermocouple male connector on the other end.

Additional Information 

PIE Calibrators are designed, assembled and calibrated in the USA. This 

product is calibrated on equipment traceable to NIST and includes a Certificate 
of Calibration. Test Data is available for an additional charge.

Practical Instrument Electronics recommends a calibration interval of one 

year. Contact your local representative for recalibration and repair services.

Содержание PIE 830PM













































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды