manualshive.com logo in svg

PIE PIE 830PM, Руководство пользователя

Поделиться
Скачать
PIE PIE 830PM Скачать руководство пользователя страница 11

Page 9

Practical Instrument Electronics

Tel: 585.872.9350 • Fax: 585.872.2638 • [email protected] • www.piecal.com

Operating Instructions

MODE - pressing the knob will cycle through OFF, LINEAR, NONLINEAR. When 
setup to read pressure SQ ROOT replaces NONLINEAR.

LINEAR turns on the mA display and regulates the loop current linear with the 
input signal. For thermocouples & RTDs this is linear relative to the temperature 
between zero and span of the sensor input. This mimics the operation of a 
digital temperature transmitter or other linearizing transmitters.
 
NONLINEAR (applies only to thermocouples and RTDs) turns on the mA 
display and regulates the loop current linear with base units (millivolts or 
ohms) of zero and span of the sensor input. This mimics the operation of an 
analog temperature transmitter without linearizing.

SQ ROOT turns on the mA display and regulates the loop current with square 
root extraction of zero and span of the pressure module input. This mimics the 
operation of a differential pressure transmitter setup for square root extraction.

BURNOUT selects the failure mode of the calibrator when the input signal is lost or 
beyond the input scale. 

Down sets the output to 1.0 mA and UP to 21.5 mA when 

sensor failure is detected.

LOOPSCOPE turns on the Loop Diagnostic display which simultaneously 
indicates the current, voltage and resistance of the loop. When enabled the 
LOOPSCOPE also indicates errors by flashing the LED and writing diagnostic 
messages on the display. Messages include 

LOW LOOP VOLT, HIGH LOOP 

VOLT and HIGH LOOP IMPED. With LOOPSCOPE on the 830PM occasionally 
performs a test on the loop. During this short test the loop mA signal will be 
affected.

Содержание PIE 830PM













































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды