background image

20

Limited PowerLight Warranty

Photogenic  Professional  Lighting  warranties the “standard line” of new
PowerLight products to be free from defects in material and workmanship
of  the  PL2  series  of  PowerLights  for  a  period  of  two  years  from
date  of  purchase.   At  our  choice,  we  will  repair or replace any PL2,
Solair  or  Voltage  Smart  series  light  that  is  deemed  to  be  defective.
This  warranty  does  not  cover  damages  caused  by  shipping,  product
abuse  or  use  other  than  the intended  photographic applications.

Any  product  modifications  will  render  this  warranty  void.   Use  of
other  manufacturer’s  accessories,   which  restrict  normal  or  intended
operation (especially venting airflow),   may cause damage and will void
this  warranty.   Flash  tubes  are  warranted  under the above conditions
for one  year  from  date  of  purchase.   Modeling lamps are covered for
initial use failures only.

Photogenic Professional Lighting

1268 Humbracht Circle, Bartlett, Illinois 60103-1631

www.PhotogenicPro.com

Telephone: (630)830-2500   Fax: (630)830-2525

MANUAL PART NO.   015756-00V3-05

Содержание PowerLight 1250





















Отзывы: