Philips Saeco Moltio Скачать руководство пользователя страница 37

Страница: 37 / 66

MOLTIO 05 SERVICE MODE

6/13

ERROR:

In the indication HEATER appears “SHORT”, the NTC

temperature-sensor is shorted, the display backlight changes from

green to red; check the wiring from the NTC temperature-sensor to

the CPU/POWER board (JP13).

ERROR:

In the indication HEATER appears “OPEN”, the NTC

temperature-sensor is detached or broken, the display backlight

changes from green to red; check the wiring from the NTC

temperature-sensor to the CPU/POWER board (JP13).

Press the COFFEE button to switch on the Heater

The absorbed current ( Amperometer on the main supply) is OK, the

indication HEATER changes from “OFF” to “ON” and the temperature

starts increasing.

If temperature is over 135°C, the backlight change from GREEN to

YELLOW. This is a ALERT message to avoid heating the HEATER

element over dangerous temperature.

ERROR:

the absorbed current is KO or the temperature does not

increase; check the wiring from the heater to the CPU/POWER

board (JP19) and the wiring of the NTC temperature-sensor (JP13).

Press CAPPUCCINO to move to the next screen

Start condition

The machine shows the three values dell’autodose

Selection beans.

The default value is 90 for all. After the coffee brewing values change (as

shown in the image)

Содержание Saeco Moltio



































































Результаты поиска

Содержание Saeco Moltio

Отзывы:

Похожие инструкции для Saeco Moltio

Бренды по названию

Популярные бренды

Philips Saeco Moltio, Руководство по обслуживанию

Результаты поиска

Содержание Saeco Moltio

Отзывы:

Похожие инструкции для Saeco Moltio

Бренды по названию

Популярные бренды