manualshive.com logo in svg

Philips M3000A, Руководство по обслуживанию

Philips M3000A - высококачественный медицинский аппарат, который обеспечивает надежное мониторирование пациентов. Для получения подробной информации о настройке и использовании устройства, вы можете бесплатно загрузить сервисный мануал на manualshive.com. Легкий доступ к руководству обеспечен для вашего удобства.

Поделиться
Скачать
background image

Battery Handling, Maintenance and Good Practices

132

  

Maintaining the Instrument

3

Turn on the monitor, and leave it on until it switches off automatically.

4

Turn the monitor off using the 

On/Off/Standby

 switch.

5

Reconnect the monitor to the AC power supply.

6

Charge the battery until it is full (the battery LED on the monitor is green).

7

Repeat steps 2 to 6.

A Note on Trickle Charging

Trickle charging means a low current is applied to a fully charged battery to keep the charge 
at 100%. (The self-discharge of NiMH batteries is in the range of 20-25% per month!). 

Trickle charging accelerates the aging of the battery and is not recommended for batteries 
that are only used occasionally. In such cases the battery should be kept separate from the 
monitor and charged every three to four months to prevent deep discharge. Deep discharge 
occurs when the battery has a relative state of charge of 0%.

NOTE

If you cannot avoid trickle charging, use the Battery Charger and Conditioner (M8043A) to 
recondition the battery once a month. See the instructions that accompany the charger for 
details on charger use.

Trickle charging only takes place for batteries stored in a monitor connected to AC mains. 
You can leave batteries in the Battery Charger and Conditioner (M8043A), as no trickle 
charging takes place.

Accessing the Battery Status Window

The Battery Status window shows additional information about the battery. To access this 
window, press the Setup key on the front panel and select Battery from the list. The Monitor 
displays a screen similar to the following:

The meaning of the messages are described in the following paragraphs.

Time to Empty—This refers to the approximate (+/- 10%) battery-usage time remaining in 
the battery. The number is based on the average monitor-loading during the previous minute.

Time to Full—This refers to the approximate (+/- 10%) time remaining to fully charge the 
battery. The number is based on the average monitor-loading during the previous minute.

 

Exit

Capacity               Current    : 284.0 mAh

Battery Status

 designed  : 2400 mAh  Cycles     :  234 

 remaining : 1247 mAh  Voltage    :  12.9 V

TimeToEmpty:  112 min +/- 10%(est. 1 min avg)

 fullCharge: 1852 mAh  Temperature:  23.0 C

Duracell TR36  12.0V SN 00292 07JUL98 SBM 1.0

Содержание M3000A






































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для M3000A

AccuMASTER 7434 User Manual preview
7434
Бренд: AccuMASTER Страницы: 2
Omer SP2 Instructions preview
SP2
Бренд: Omer Страницы: 2
4iiii PRECISION Firmware Upgrade Instructions preview
PRECISION
Бренд: 4iiii Страницы: 3
Hach PLATINUM Series Manual preview
PLATINUM Series
Бренд: Hach Страницы: 64
Navman A300 Sport.Tool Specification preview
A300 Sport.Tool
Бренд: Navman Страницы: 1
WATERGUARD Puddle Installation Manual preview
Puddle
Бренд: WATERGUARD Страницы: 2
OBDPROG MT401 Manual preview
MT401
Бренд: OBDPROG Страницы: 8
Keysight M8290A Getting Started Manual preview
M8290A
Бренд: Keysight Страницы: 56
Chauvin Arnoux AEMC 2139.61 User Manual preview
AEMC 2139.61
Бренд: Chauvin Arnoux Страницы: 64
S+S Regeltechnik 1101-3121-0049-800 Operating Instructions, Mounting & Installation preview
1101-3121-0049-800
Бренд: S+S Regeltechnik Страницы: 16
Vector 5200-00 User Manual preview
5200-00
Бренд: Vector Страницы: 8
Keysight Technologies M9602A Configuration Manual preview
M9602A
Бренд: Keysight Technologies Страницы: 10
Fluke 80i-2010s Instructions Manual preview
80i-2010s
Бренд: Fluke Страницы: 8
MetLogix Mx200 User Manual preview
Mx200
Бренд: MetLogix Страницы: 30
TDE Instruments Digalox DPM72-MPPV Instruction Manual preview
Digalox DPM72-MPPV
Бренд: TDE Instruments Страницы: 8
jenway 3345 Operating Manual preview
3345
Бренд: jenway Страницы: 53
Hanna Instruments IC-HI98165 Instruction Manual preview
IC-HI98165
Бренд: Hanna Instruments Страницы: 52
Accurate Technology ProScale 950 Series Quick Start Manual preview
ProScale 950 Series
Бренд: Accurate Technology Страницы: 16

Бренды по названию

Популярные бренды

Загрузить еще бренды