manualshive.com logo in svg

Philips LPC2119, Руководство пользователя

Скачайте бесплатное руководство пользователя для продукта Philips LPC2119 на manualshive.com. Получите подробное описание и инструкции по использованию этого устройства. Загрузите руководство сейчас и начните использовать ваш продукт эффективно.

Поделиться
Скачать
background image

System Control Block

67

January 08, 2004

Philips Semiconductors

Preliminary User Manual

LPC2119/2129/2292/2294

ARM-based Microcontroller

VPB DIVIDER

The VPB Divider determines the relationship between the processor clock (cclk) and the clock used by peripheral devices (pclk). 
The VPB Divider serves two purposes. The first is to provides peripherals with desired pclk via VPB bus so that they can operate 
at the speed chosen for the ARM processor. In order to achieve this, the VPB bus may be slowed down to one half or one fourth 
of the processor clock rate. Because the VPB bus must work properly at power up (and its timing cannot be altered if it does not 
work since the VPB divider control registers reside on the VPB bus), the default condition at reset is for the VPB bus to run at 
one quarter speed. The second purpose of the VPB Divider is to allow power savings when an application does not require any 
peripherals to run at the full processor rate.

The connection of the VPB Divider relative to the oscillator and the processor clock is shown in Figure 16. Because the VPB 
Divider is connected to the PLL output, the PLL remains active (if it was running) during Idle mode.

VPBDIV Register (VPBDIV - 0xE01FC100)

The VPB Divider register contains two bits, allowing three divider values, as shown in Table 34.

Table 33: VPBDIV Register Map

Address

Name

Description

Access

0xE01FC100

VPBDIV

Controls the rate of the VPB clock in relation to the processor clock.

R/W

Table 34: VPB Divider Register (VPBDIV - 0xE01FC100)

VPBDIV

Function

Description

Reset 

Value

1:0

VPBDIV

The rate of the VPB clock is as follows:
0 0: VPB bus clock is one fourth of the processor clock.
0 1: VPB bus clock is the same as the processor clock.
1 0: VPB bus clock is one half of the processor clock. 
1 1: Reserved. If this value is written to the VPBDIV register, it has no effect (the 
previous setting is retained).

0

3:2

Reserved

Reserved, user software should not write ones to reserved bits. The value read from a 
reserved bit is not defined.

0

5:4

XCLKDIV

In the LPC2292/2294 (parts in 144 packages) only, these bits control the clock that can 
be driven onto the A23/XCLK pin. They have the same encoding as the VPBDIV bits 
above. A bit in the PINSEL2 register (Pin Connect Block on page 100) controls whether 
the pin carries A23 or the clock selected by this field.

Note: If this field and VPBDIV have the same value, the same clock is used on the 
VPB and XCLK.

 (This might be useful for external logic dealing with the VPB 

peripherals).

0

7:6

Reserved

Reserved, user software should not write ones to reserved bits. The value read from a 
reserved bit is not defined.

0

Содержание LPC2119














































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для LPC2119

Lattice Semiconductor CrossLink Programming And Configuration Manual preview
CrossLink
Бренд: Lattice Semiconductor Страницы: 30
Tapeswitch C6 Technical Manual preview
C6
Бренд: Tapeswitch Страницы: 13
Kamstrup M-Bus Manual preview
M-Bus
Бренд: Kamstrup Страницы: 36
L. G. B. 51099 Instructions preview
51099
Бренд: L. G. B. Страницы: 2
L-Acoustics LA4X Product Information preview
LA4X
Бренд: L-Acoustics Страницы: 36
B&G ZEUS S Detailed App Manual preview
ZEUS S
Бренд: B&G Страницы: 19
Wesa AE04 Installation And Operation Manual preview
AE04
Бренд: Wesa Страницы: 8
micro-trak MT-3405 LR F Reference Manual preview
MT-3405 LR F
Бренд: micro-trak Страницы: 44
Sonos Controller CR100 Quick Setup Instructions Manual preview
Controller CR100
Бренд: Sonos Страницы: 12
Halma Alicat Scientific MC Quick Start Manual preview
Alicat Scientific MC
Бренд: Halma Страницы: 2
Avenview SW-HBT4K-C6-4X4E Quick Start Manual preview
SW-HBT4K-C6-4X4E
Бренд: Avenview Страницы: 8
Eaton Jockey XTJP O & M Manual preview
Jockey XTJP
Бренд: Eaton Страницы: 12
Renishaw PHC10-3 PLUS Installation Manual preview
PHC10-3 PLUS
Бренд: Renishaw Страницы: 68
Aqua Lung Legend LX Second Stage Technical Maintenance Manual preview
Legend LX Second Stage
Бренд: Aqua Lung Страницы: 18
LMF Manufacturing HPH User Manual preview
HPH
Бренд: LMF Manufacturing Страницы: 51
American DJ GALATIC STAR 19C User Instructions preview
GALATIC STAR 19C
Бренд: American DJ Страницы: 1
Cairox TSCTK-1 Series Original User Manual preview
TSCTK-1 Series
Бренд: Cairox Страницы: 3
Heatpol HOME+ H+h WiFi Manual & User Manual preview
HOME+ H+h WiFi
Бренд: Heatpol Страницы: 10

Бренды по названию

Популярные бренды

Загрузить еще бренды