manualshive.com logo in svg

Philips LPC2119, Руководство пользователя

Скачайте бесплатное руководство пользователя для продукта Philips LPC2119 на manualshive.com. Получите подробное описание и инструкции по использованию этого устройства. Загрузите руководство сейчас и начните использовать ваш продукт эффективно.

Поделиться
Скачать
background image

Pulse Width Modulator (PWM)

202

January 08, 2004

Philips Semiconductors

Preliminary User Manual

LPC2119/2129/2292/2294

ARM-based Microcontroller

PWM Latch Enable Register (PWMLER - 0xE0014050)

ThePWM Latch Enable Register is used to control the update of the PWM Match registers when they are used for PWM 
generation. When software writes to the location of a PWM Match register while the Timer is in PWM mode, the value is held in 
a shadow register. When a PWM Match 0 event occurs (normally also resetting the timer in PWM mode), the contents of shadow 
registers will be transferred to the actual Match registers if the corresponding bit in the Latch Enable Register has been set. At 
that point, the new values will take effect and determine the course of the next PWM cycle. Once the transfer of new values has 
taken place, all bits of the LER are automatically cleared. Until the corresponding bit in the PWMLER is set and a PWM Match 0 
event occurs, any value written to the PWM Match registers has no effect on PWM operation.

For example, if PWM2 is configured for double edge operation and is currently running, a typical sequence of events for changing 
the timing would be:

• Write a new value to the PWM Match1 register.

• Write a new value to the PWM Match2 register.

• Write to the PWMLER, setting bits 1 and 2 at the same time.

• The altered values will become effective at the next reset of the timer (when a PWM Match 0 event occurs).

The order of writing the two PWM Match registers is not important, since neither value will be used until after the write to 
PWMLER. This insures that both values go into effect at the same time, if that is required. A single value may be altered in the 
same way if needed. 

The function of each of the bits in the PWMLER is shown in Table 170.

Table 170: PWM Latch Enable Register (PWMLER - 0xE0014050)

PWMLER

Function

Description

Reset 

Value

0

Enable PWM 

Match 0 Latch

Writing a one to this bit allows the last value written to the PWM Match 0 register to be 
become effective when the timer is next reset by a PWM Match event. See the 
description of the PWM Match Control Register (PWMMCR).

0

1

Enable PWM 

Match 1 Latch

Writing a one to this bit allows the last value written to the PWM Match 1 register to be 
become effective when the timer is next reset by a PWM Match event. See the 
description of the PWM Match Control Register (PWMMCR).

0

2

Enable PWM 

Match 2 Latch

Writing a one to this bit allows the last value written to the PWM Match 2 register to be 
become effective when the timer is next reset by a PWM Match event. See the 
description of the PWM Match Control Register (PWMMCR).

0

3

Enable PWM 

Match 3 Latch

Writing a one to this bit allows the last value written to the PWM Match 3 register to be 
become effective when the timer is next reset by a PWM Match event. See the 
description of the PWM Match Control Register (PWMMCR).

0

4

Enable PWM 

Match 4 Latch

Writing a one to this bit allows the last value written to the PWM Match 4 register to be 
become effective when the timer is next reset by a PWM Match event. See the 
description of the PWM Match Control Register (PWMMCR).

0

5

Enable PWM 

Match 5 Latch

Writing a one to this bit allows the last value written to the PWM Match 5 register to be 
become effective when the timer is next reset by a PWM Match event. See the 
description of the PWM Match Control Register (PWMMCR).

0

6

Enable PWM 

Match 6 Latch

Writing a one to this bit allows the last value written to the PWM Match 6 register to be 
become effective when the timer is next reset by a PWM Match event. See the 
description of the PWM Match Control Register (PWMMCR).

0

7

Reserved

Reserved, user software should not write ones to reserved bits. The value read from 
a reserved bit is not defined.

NA

Содержание LPC2119














































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для LPC2119

Galcon 61 Series Installation And Operating Instructions Manual preview
61 Series
Бренд: Galcon Страницы: 35
ZKTeco F6 Installation Manual preview
F6
Бренд: ZKTeco Страницы: 2
FASAR ELETTRONICA FE230 Quick Start Manual preview
FE230
Бренд: FASAR ELETTRONICA Страницы: 2
Faro 33928 Installation Manual preview
33928
Бренд: Faro Страницы: 3
YASKAWA G7 Series Technical Manual preview
G7 Series
Бренд: YASKAWA Страницы: 456
S&C 6802 Application Manual preview
6802
Бренд: S&C Страницы: 8
OJ Electronics EFR Series Instructions Manual preview
EFR Series
Бренд: OJ Electronics Страницы: 8
OJ Electronics ETO2 Manual preview
ETO2
Бренд: OJ Electronics Страницы: 112
OJ EFS Series Instructions Manual preview
EFS Series
Бренд: OJ Страницы: 17
Idex Pulsafeeder MPC Vector Installation, Operation & Maintenance Manual preview
Pulsafeeder MPC Vector
Бренд: Idex Страницы: 114
Burkert 8745 MFC Ethernet Operating Instructions Manual preview
8745 MFC Ethernet
Бренд: Burkert Страницы: 70
Kelly KLS7250H User Manual preview
KLS7250H
Бренд: Kelly Страницы: 35
Pro-face LT-4201TM Installation Manual preview
LT-4201TM
Бренд: Pro-face Страницы: 48
ISC APECS Operational Instructions preview
APECS
Бренд: ISC Страницы: 20
Inca PSJ2 User Manual preview
PSJ2
Бренд: Inca Страницы: 11
OCTANORM M 1497-4 User Manual preview
M 1497-4
Бренд: OCTANORM Страницы: 6
Quicksmart EtherRain User Manual preview
EtherRain
Бренд: Quicksmart Страницы: 10
Aerotech Ensemble HLe Hardware Manual preview
Ensemble HLe
Бренд: Aerotech Страницы: 112

Бренды по названию

Популярные бренды

Загрузить еще бренды