background image

Smart energy plug  PAN38

     

This plug-in ON/OFF switch PAN38 is a security enabled wireless switch, based on Z-

Wave Plus technology. Z-Wave Plus

TM

  enabled devices displaying the Z-Wave Plus

TM

logo can also be used with it regardless of the manufacturer, and can also be used in

other manufacturer’s Z-Wave

TM

  enabled networks. Remote On/Off control of the con-

nected load is possible with another manufacturer’s wireless Controller. Each switch is

designed to act as a repeater. Repeaters will re-transmit the RF signal to ensure that the

signal is received by its intended destination by routing the signal around obstacles and

radio dead spots. Because PAN38 supports Security Command Class, it can learn with

Secured controller. Its functionality and supported command classes are identical when

included as a secure and non-secure device.

This plug-in ON/OFF switch is able to detect instance wattage (3000W/230VAC/13A)

and overload current (14.5A with resistive load) of connected lights or appliances. When

detecting overload state, the Switch will be disabled and it’s On/Off button will be lock-

out of which LED will flash quickly.  However, unplug and reconnect the switch will re-

set its overload condition to normal status.

Specification

Operating Voltage

100V-240V~  50Hz-60Hz

Maximum Load (Ampere)

13A (Resistive load) PAN38-1; PAN38-2; PAN38-3

Maximum Load (Ampere)

10A (Resistive load) PAN38-4 (Switzerland)

Socket Type:

Germany type: PAN38-1

France type: PAN38-2

UK type: PAN38-3

Switzerland type: PAN38-4

Range

Minimum 40 m in door 100m outdoor line of sight

Operating Temperature

0°C ~ 40°C

Frequency Range

868.40MHz & 869.85MHz/ EU (PAN38-1/-2/-3/-4); 

RF Maximum Power

+10dBm (Peak), -10dBm (Average)

 

** Specifications are subject to change and improvement without notice. 

Troubleshooting

 

Symptom

Cause of Failure

Recommendation

The   Switch   not   working

and LED off

1.The   Switch   is   not   plugged   into

the electrical outlet properly

2.The Switch break down

1. Check power connections

2. Don’t open up the Switch

and send it for repair.

The   Switch   LED   illumi-

nating, but cannot control

the Switch of the load at-

tached

1.Check   if   the   load   plugged   into

the   Switch   has   its   own   ON/OFF

switch

2. The switch is protected

1. Set the ON/OFF switch of

the load attached to ON

2. Unprotected the switch or

follow the instruction of pro-

tection.

The   Switch   LED   illumi-

nating,   but  the  Detector

cannot control the Switch

1. Not carry out association

2. Same frequency interference

1. Carry out association

2. Wait for a while to re-try

LED   keep   flashing,   but

cannot control

Overload occurs

Remove the load attached or

check   max.   load   cannot   ex-

ceed 13A (Resistive load)

Содержание PAN38











Отзывы: