background image

Disposal

 

This marking indicates that this product should not be disposed

with other household wastes throughout the EU. To prevent possi-

ble harm to the environment or human health from uncontrolled

waste disposal, recycle it responsibly to promote the sustainable

reuse of material resources. To return your used device, please use

the return and collection systems or contact the retailer where the

product was purchased. They can take this product for environ-

mental safe recycling.

Company of License Holder

Philio Technology Corporation

Address of License Holder

8F., No.653-2, Zhongzheng Rd., Xinzhuang Dist.,

New Taipei City 24257, Taiwan(R.O.C)

www.philio-tech.com

FCC Interference Statement

This equipment has been tested and found to comply with the limits for a Class B

digital device, pursuant to Part 15 of the FCC Rules. 

These limits are designed to provide reasonable protection against harmful inter-

ference in a residential installation. 

This equipment generates, uses and can radiate radio frequency energy and, if not

installed and used in accordance with the instructions, may cause harmful inter-

ference to radio communications. 

However, there is no guarantee that interference will not occur in a particular in-

stallation. 

If this equipment does cause harmful interference to radio or television reception,

which can be determined by turning the equipment off and on, the user is encour-

aged to try to correct the interference by one of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which

the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

This device complies with Part 15 of the FCC Rules. Operation is subject to the follow-

ing two conditions:

(1)This device may not cause harmful interference.

(2)This device must accept any interference received, including interference that may

cause undesired operation.

FCC Caution: Any changes or modifications not expressly approved by the party respon-

sible for compliance could void the user's authority to operate this equipment.

This transmitter must not be co-located or operating in conjunction with any other an -

tenna or transmitter.

Содержание PAN38











Отзывы: