background image

type

6

Level 

report 

mode

1

1-2

2

1:

Report destination 

level in 5s

2:

Report 10 percent 

level while running

7-1 Watt Meter Report Period:

If the setting is configured for 1hour (set value =720), the PAN08 will report its instant

power consumption every 1 hour to the node of Group 1. The maximum interval to 

report its instant power consumption is 45 hours (5s*32767/3600=45hr). Default 

value is 1 hour.

7-2 KWH Meter Report Period:

      If   the   setting   is   configured   for   1hour   (set   value   =6),   the   PAN08   will   report   its

Accumulated Power Consumption (KW/h) every 1 hour to the node of correspond

Group. The maximum interval to report its Accumulated Power Consumption (KW/h)

is 227.55 days (10min*32767/1440=227.55 days). Default value=1 hour.

7-3 Threshold of current for Load Caution

This is a warning when the current of load over the preset threshold value, if the

setting value is 500, when the load current of Relay1 over this value, PAN08

will send current meter report to warn the Group1 node, the Range of the setting

value is from 10 to 500, and the default value is 500.

7-4 Threshold of KWh for Load Caution

This is a warning when the KWh of load over the preset threshold value, If the setting

value is 10000, when the Accumulated Power Consumption of Relay1 or Relay2 over

this value, PAN08 will send KWh Meter Report command to the node of correspond 

Group, minimum value is 1KWh and default value is 10000 kWh

7-5 External switch type

7-5-1 One Push Button

 

When the configuration setting is One Push Button, only S1 input will be valid. 

The control moving commands can be accepted in this switch type while the 

shutter is moving. In this switch type, the inclusion/exclusion/reset/association 

function can also be fulfilled by pressing S1 just like the operation of include 

button.

  When S1 is short pressed, the shutter will move up toward TOP(0xFF). While in 

this moving S1 is short pressed again, the shutter will stop moving. A third short 

pressing of S1 will move the shutter down toward BOTTOM(0x00). While in this 

moving S1 is short pressed again, the shutter will stop moving. And so on… 

Inverting direction and stopping.

7-5-2 Two Push Button

 (The default setting is Two Push Button (2))

If this setting is configured as Two Push Button, S1 and S2 input will be valid, but

will not accept pressing S1and S2 at the same time. In this switch type, the 

inclusion/exclusion/reset/association function can also be fulfilled by pressing S1

or S2 just like the operation of include button.

When S1 is pressed and hold more than 1.5 seconds, the shutter will move up 

toward TOP(0xFF), and the shutter will stop moving when S1 is released. When 

S2 is pressed and hold more than 1.5 seconds, the shutter will move down 

toward BOTTOM(0x00), and the shutter will stop moving when S2 is released.    

  When S1 is short pressed, the shutter will move up toward TOP(0xFF).  While in 

this moving short pressed S1 again, the shutter just keep moving up toward 

11

Содержание PAN08-1A















Отзывы: