manualshive.com logo in svg

Philio PAN04, Руководство пользователя

Поделиться
Скачать
Philio PAN04 Скачать руководство пользователя страница 4

Installation

1. Put the in wall switch into a wall box and connect the AC power wire L,N to

PAN04 connector L, N.

2. Connect the wall switch to the PAN04 as Fig1 .

3. To manually turn ON the Switch, press and release the On/Off button. The

LED will light ON for 1 second, and the load plugged into the Switch will

also turn ON.

4. To   manually   turn   OFF   the   Switch,   simply   press   and   release   the   On/Off

button. The LED will light ON for 1 second and the load plugged into the

Switch will turn OFF.

Programming

1.  Basic Command Class / Binary Switch Command Class

The Switch will respond to BASIC and BINARY  SWITCH  commands that

are part of the Z-Wave system.

1-1 BASIC_GET / BINARY_SWITCH_GET

Since the switch have two relay, the Switch will report its On/Off state to

the Controller by setting Configuration parameter 3.

Configuration parameter 3=1   Report ON when relay 1 ON

Report OFF when relay 1 OFF 

Configuration parameter 3=2   Report ON when relay 2 ON 

     Report OFF when relay 2 OFF

Configuration parameter 3=3 (default) 

Report ON when either relay 1 ON or relay 2 ON

    Report OFF when both relay 1 and relay 2 OFF

    

4

Содержание PAN04





















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды