Pfaff 8320-010 Скачать руководство пользователя страница 8

Страница: 8 / 110

Safety

.05

Operating and technical staff

.05.01

Operating staff

Operating staff are the persons responsible for setting up, operating and cleaning the machi-

ne and for removing any disturbances in the sewing area.

The operating staff is obliged to observe the following points, and must:

●

always observe the notes on safety in this instruction manual!

●

avoid using any working methods which adversely affect the safety of the machine!

●

avoid wearing loose-fi tting clothing or jewelry such as necklaces or rings!

●

also ensure that only authorized persons are allowed near the danger area of the machine!

●

immediately report to the user any changes to the machine that may affect its safety!

.05.02

Technical staff

Technical staff are persons who have been trained in electrical engineering, electronics and

mechanical engineering. They are responsible for lubricating, servicing and repairing the ma-

chine.

The technical staff is obliged to observe the following points, and must:

●

always observe the notes on safety in this instruction manual!

●

switch off the on/off switch before carrying out any maintenance and repair work on the

machine!

●

never work on parts or equipment still connected to the power supply! Exceptions to this

are only permissible according to regulations EN

50110

●

replace all safety covers after maintenance and repair work!

Содержание 8320-010















































































































Результаты поиска

Содержание 8320-010

Отзывы:

Похожие инструкции для 8320-010

Бренды по названию

Популярные бренды

Pfaff 8320-010, Инструкция по эксплуатации

Результаты поиска

Содержание 8320-010

Отзывы:

Похожие инструкции для 8320-010

Бренды по названию

Популярные бренды