background image

PRODUCTS DANGER SYMBOLS USED

3

Reproduction or translation, even partial, is forbidden without the written consent of Peugeot Motocycles

PRODUCTS DANGER SYMBOLS USED

Protection of individuals and of the environment. 

Möbius band

Recyclable. 

Means that the product or the package 
can be recycled. However, this does not 
guarantee that the product will be 
recycled. 

Irritant

The product can irritate the 
skin, eyes and respiratory 
organs. 

Avoid contact with skin and clothes. Wear 
gloves, safety glasses and appropriate 
clothing such as a cotton overall. Do not 
breath fumes. If in contact, wash 
thoroughly with water. 

Flammable

The product is flammable. 

Keep it away from flames or any heat 
source (barbecue, radiator, heating, etc.). 
Do not leave the product in the sun. 

Corrosive

The product can damage living 
tissues or other surfaces. 

Avoid contact with skin and clothes. Wear 
gloves, safety glasses and appropriate 
clothing such as a cotton overall. Do not 
breath fumes. 

Explosive

The product can explode under 
certain circumstances (flame, 
heat, impact, friction). 

Avoid impacts, friction, sparks and heat. 

Hazardous to 
the environment

The product affects fauna and 
flora. Do not dump it in 
dustbins, sinks or in the 
environment. 

The ideal solution is to bring this product 
to your nearest household waste recycling 
centre. 

Toxic

The product can seriously 
affect health if it is inhaled, 
ingested or in contact with skin. 

Avoid direct contact with the body, even by 
inhalation. If you feel unwell, seek medical 
advice immediately. 

Do not throw 
away into a 
garbage can

One of the product's 
component is toxic and can be 
hazardous to environment. For 
example: Used batteries. 

This symbol informs the consumer that the 
used product shall not be thrown away into 
a garbage can, but shall be brought back 
to the merchant or dropped at a specific 
collection point. 

Compulsory 
gloves

Operation that can be 
dangerous for people. 

People's safety can be seriously affected if 
the recommendations are not fully 
respected. 

Содержание XS1P52QMI-4

















































Отзывы: