PEUGEOT XS1P52QMI-4 страница 16 Скачать руководство пользователя

Страница: 16 / 48

PRIMARY TRANSMISSION

Reproduction or translation, even partial, is forbidden without the written consent of Peugeot Motocycles

- Remove the clutch linings (2), the upper

centring sleeve (3), the spring (4), and the
lower centring sleeve (5).

- Remove the 3 pins (6) from the variable

speed drive seat.

- Separate the fixed (7) and rotating (8) flanges.
- Make sure surface of the plates in contact with

the belt does not show any cracks or signs of
abnormal wear.

Refitting the clutch lining assembly

- After checking the 2 lip seals (9) and the 2 O-

rings (10) of the rotating flange (8) are in good
condition, grease the governor seat 3 pins (6)
(high temperature grease) and assemble the
parts in reverse order to removal.

- Compress the clutch and driven pulley

assembly using tool 758008 equipped with
the protection spacer P/N 801682.

- Tighten the nut (1).

Tightening torque: 55 Nm.

Before fitting the clutch drive pulley and
driven pulley to the input shaft, fit the
belt into the pulley bottom by opening
the flanges by hand.

- Fit the clutch drive pulley and driven pulley

assembly.

- Fit the clutch cover.
- Fit and tighten the nut.

Tightening torque: 45 Nm.

- Fit the 2 locating pins and a new paper gasket.
- Fit the drive pulley with its guide hub onto the

connecting rod.

- Fit and tighten the nut.

Tightening torque: 55 Nm.

- Install the transmission cover (8 screws).

Tightening torque: 10 Nm.

Содержание XS1P52QMI-4

















































Результаты поиска

Содержание XS1P52QMI-4

Отзывы:

Похожие инструкции для XS1P52QMI-4

Бренды по названию

Популярные бренды

PEUGEOT XS1P52QMI-4, Руководство по ремонту

Результаты поиска

Содержание XS1P52QMI-4

Отзывы:

Похожие инструкции для XS1P52QMI-4

Бренды по названию

Популярные бренды