PEUGEOT ENERGYSand-100, Руководство пользователя

Страница: 4 / 34

4 5 4 5
setting the tool
5. Push the belt by hand and check to see if the
sanding belt tends to run to one side or the
other on the two drums.
6. If the sanding belt runs toward disc, slightly
turn the tracking knob (6) counterclockwise.
7. If the sanding belt runs away from the disc,
slightly turn the tracking knob (6) clockwise.
8. Plug sander into power source and turn the
switch ON and OFF quickly, and check to
see if the sanding belt moves to either side.
Re-adjust and fine tune tracking knob if
necessary.
9. When proper tracking is achieved, replace
dust chute (2).
changing Position of sanDing belt
table
sanding table in vertical position (fig. 15, 16)
note: The sanding table (1) can be used in
either the horizontal or vertical position.
1. To move the sanding table (1), loosen the two
bolts (2) with the supplied wrench (3) from the
slots of the side pulley cover that attach table
to the main body.
2. Move the sanding table (1) to the desired
position.
3. Tighten the two bolts (2).
4. Remove the disc/belt table and rod (3) from
the sanding disc area by removing the hex
bolt near base. (Fig. 16)
5. Place the hex bolt (4) into the threaded hole
near the auxiliary hole.
6. Slide the rod (3) into the auxiliary hole for the
belt table (5) until the table is 1.59 mm from
sanding belt. (Fig. 16)
7. Align flat surface onto support rod with hex
bolt (6) on table bracket and tighten the bolt
(6).
leveling the arM (fig. 17)
A positive table stop (4) is provided to position
the sanding table level with workbench when the
table is in the horizontal position.
1. Place the sanding table (1) in the horizontal
position.
2. Place a level (2) on the sanding belt and
check to see if the table is level.
3. If an adjustment is necessary, loosen lock
nut (3), and turn the sanding table stop (4)
clockwise to raise, or counterclockwise to
lower, until the sanding table is level.
4. Tighten the lock nut (3).
aDjUsting Disc table sqUare with
sanDing Disc (fig. 11)
1. Using a combination square (1), place one
side of the square on the disc table assembly
(2) with the other side against the sanding
disc (3), and check to see if the disc table is
90° to the disc.
2. If the disc table surface is not 90° to the disc,
loosen the table lock knob (4), adjust table
square with disc and tighten the table lock
knob (4).
3. Adjust pointer (5) to the 0° mark on the angle
scale using a screwdriver.
aDjUsting Disc table angle (fig. 12)
1. The disc table (1) can be tilted from 0° to 45°
by loosening the table lock knob (2).
2. Tilt the disc table (1) to the desired angle.
3. Tighten table lock knob (2).
rePlacing sanDing belt anD tracking
belt (fig. 13, 14)
1. Remove the dust chute (2) from belt by
loosening the two screws (1) (Fig. 13).
2. Slide tension lever (3) to the right to release
tension on the sanding belt (4). (Fig. 14)
3. Remove sanding belt from both sanding
drums (5).
4. Slide new sanding belt over sanding drums.
Making sure the belt arrow located on the
inside of the belt will run in the right direction.
Slide tension lever (3) to the left to apply belt
tension.
warning! to avoid injury, always keep the
plug disconnected from the power source
and the switch turned off until the sander is
completely assembled and adjusted properly.
warning! to avoid trapping the workpiece
or fingers between the table and sanding
disc, the disc table edge should positioned
a maximum of 1.59 mm from sanding disc
plate.
warning! after tilting the table, the assembly
must be repositioned on the support rod by
loosening the bolt (3) to a maximum of 1.59
mm distance between the sanding disc and
the edge of the disc table, to avoid trapping
the work or finger between the disc and disc
table.
warning! to avoid injury, turn switch off
and disconnect the plug from the power
source before removing and installing
sanding belt.
warning! to avoid trapping the workpiece
or fingers between the table and sanding
belt, the table edge should be positioned a
maximum of 1.59 mm from sanding belt.