PEUGEOT ELYSTAR Скачать руководство пользователя страница 40 | Manualshive

Страница: 40 / 49

background image

WORKING ON THE ABS/PBS SYSTEM

Page : 40

Reproduction or translation, even partial, are forbidden without the written consent of Peugeot Motocycles

Important:

It is essential to avoid being under the

master cylinder during bleeding to avoid brake
fluid splashes

- Operate the brake lever

evenly and smoothly

whilst topping up the fluid in the master cylinder

- Stop when there are no more bubbles coming from the control unit bleed screw
- Close the bleed screw
- Disconnect the pipe connecting it to the recipient
- Using the diagnostic tool operate the pump to assess lever firmness

Note:

If the lever does not feel sufficiently hard, bleed the power braking circuit.

- Operate the brake lever again slowly to check there are no more bubbles in the circuit
- Check the brake fluid level in the master cylinder, top up if necessary and fit the cover

Important

: The brake fluid level in the master cylinders in the horizontal position must always be above the

sight gauge level.

- Re-fit the bleed screw cap

Note:

If the lever does not feel sufficiently firm, repeat the control unit bleed operation.

«
...
38
39
40
41
42
...
»

Содержание ELYSTAR


















































Отзывы:

Нет отзывов

Похожие инструкции для ELYSTAR

Бренд: Mega Motion Страницы: 39

Electric Party POP

Бренд: Razor Страницы: 12

Бренд: RACCEWAY Страницы: 60

Бренд: SXT Страницы: 22

Бренд: NAVEE Страницы: 16

Бренд: Riding'Times Страницы: 55

Бренд: Hover-1 Страницы: 26

INSTINCT H1-EGBR

Бренд: Hover-1 Страницы: 33

Бренд: Razor Страницы: 2

Бренд: Razor Страницы: 6

WILD ONES Series

Бренд: Razor Страницы: 8

Бренд: Razor Страницы: 15

Бренд: Razor Страницы: 20

Бренд: Razor Страницы: 36

Бренд: Razor Страницы: 41

Бренд: HYOSUNG Страницы: 257

Бренд: BMX Страницы: 5

Бренд: Kaabo Страницы: 21

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды