manualshive.com logo in svg

PEUGEOT ELYSTAR, Руководство по ремонту

PEUGEOT ELYSTAR - роскошный и стильный мотоцикл, который предлагает Workshop Manual для бесплатного скачивания. Этот manual поможет вам легко обслуживать ваше устройство. Скачайте его с manualshive.com и получите детальные инструкции по использованию и обслуживанию вашего PEUGEOT ELYSTAR.

Поделиться
Скачать
background image

WORKING ON THE ABS/PBS SYSTEM

Page : 25

Reproduction or translation, even partial, are forbidden without the written consent of Peugeot Motocycles

Incidents which cannot be detected by the ECU

These incidents are not detected by the ECU and do not show a fault code.

Loss of braking pressure, brake lever soft: (warning light off)

Checks:
-

 

Check the brake fluid level in the levers

-

 

Check operation of the conventional part of the brakes, calipers, pads, unions, etc

-

 

Check the brake fluid level in the control unit reservoir

-

 

Bleed the brake system and check there is no air in the circuit

-

 

Check the electrical power supply to the control unit, battery charge, harness connections, etc

if the checks prove OK and the fault persists, change the control unit

Harsh and non-progressive braking: (warning light off)

-

 

Change the control unit

Warning light does not go off at a speed of over 5 km/h but goes off after braking and no fault code: (warning

light on)
Checks:
-

 

Check the right and left contactors

-

 

Check the brake contactor harness, continuity, isolation

-

 

Check the warning light harness, continuity, isolation

-

 

Check the speed sensor, wrong gap, pulse wheel distorted, sensor faulty, etc

-

 

Check the control unit electric motor, terminal 15 and terminal 18

If these checks prove OK and the fault persists, change the control unit

Warning light does not go off at a speed of over 5 km/h even after braking and no fault code: (warning light

on)
Checks:
-

 

Check the right and left contactors

-

 

Check the brake contactor harness, continuity, isolation

-

 

Check the warning light harness, continuity, isolation

If these checks prove OK and the fault persists, change the control unit

Electric pump operates permanently with no effect on brakes: (warning light on)

Checks:
-

 

Cut off the ignition and turn on again

-

 

Check the right and left contactors

-

 

Check the brake contactor harness, continuity, isolation

-

 

Check the warning light harness, continuity, isolation

-

 

Check the speed sensor, wrong gap, pulse wheel distorted, sensor faulty, etc

-

 

Check the control unit electric motor, terminal 15 and terminal 18

If these checks prove OK and the fault persists, change the control unit

Содержание ELYSTAR


















































Отзывы:

Нет отзывов

Похожие инструкции для ELYSTAR

E-TON AV05W9-A Owner'S Manual preview
AV05W9-A
Бренд: E-TON Страницы: 31
Hover-1 DSA-EDGE Operation Manual preview
DSA-EDGE
Бренд: Hover-1 Страницы: 29
Aosom AIYAPLAY AA1-106V70 Instruction Manual preview
AIYAPLAY AA1-106V70
Бренд: Aosom Страницы: 37
Yamaha YDX TORC PB65YTL Assembly Manual preview
YDX TORC PB65YTL
Бренд: Yamaha Страницы: 16
Yamaha XCITY VP250 Owner'S Manual preview
XCITY VP250
Бренд: Yamaha Страницы: 82
Yamaha XCITY 125 Owner'S Manual preview
XCITY 125
Бренд: Yamaha Страницы: 82
Yamaha Xenter HW151 Owner'S Manual preview
Xenter HW151
Бренд: Yamaha Страницы: 84
Yamaha XC125RR Owner'S Manual preview
XC125RR
Бренд: Yamaha Страницы: 84
Yamaha X Max 400 Owner'S Manual preview
X Max 400
Бренд: Yamaha Страницы: 92
Yamaha YW50AP Service Manual preview
YW50AP
Бренд: Yamaha Страницы: 214
Yamaha YJ125S Service Manual preview
YJ125S
Бренд: Yamaha Страницы: 294
WESTHILL BIKES CLASSIC User Manual preview
CLASSIC
Бренд: WESTHILL BIKES Страницы: 20
Shoprider Paris GK9 User Manual preview
Paris GK9
Бренд: Shoprider Страницы: 20
Glide Cruisers Calisto Owner'S Manual preview
Calisto
Бренд: Glide Cruisers Страницы: 14
Glide G2 Series User Manual preview
G2 Series
Бренд: Glide Страницы: 20
Promovec MK FIVE User Manual preview
MK FIVE
Бренд: Promovec Страницы: 24
X-TREME XM-5000Li Operation And Maintenance Instructions preview
XM-5000Li
Бренд: X-TREME Страницы: 21
X-TREME XMB-400 Owner'S Manual preview
XMB-400
Бренд: X-TREME Страницы: 34

Бренды по названию

Популярные бренды

Загрузить еще бренды