background image

FIRE ALARM ASPIRATION SENSING TECHNOLOGY® 

INSTALLATION AND MAINTENANCE GUIDE 

ADDRESSABLE FAAST LT : MODELS FL2011EI, FL2012EI AND FL2022EI 

 

 

© Pertronic Industries Ltd 

FAAST LT Loop-Based Installation & Maintenance Guide  Iss 1.0, 201701

 

36

7

m

m

135 mm

56 mm

44 mm

40

3

m

m

356 mm

DESCRIPTION 

 
 
 
 
 
 
 
 
 
 
 
 
 
 

The  FAAST  LT  Series  is  part  of  the  Fire  Alarm 
Aspiration  Sensing  Technology®  (FAAST)  family.  
FAAST  is  an  advanced  fire  detection  system  for  use 
where  early  warning  and  very  early  warning  are  a 
requirement.  The  system  continuously  draws  air  from 
the controlled environment through a series of sampling 
holes to monitor the environment for smoke particulate. 
The  FL20  Series  is  the  addressable  version  of  the 
FAAST  LT  range,

 

communicating  with  the  Fire  Panel 

via a proprietary loop protocol. 
The FL20nnEI is available in 3 different models each, 6 
models total: 

FL2011EI

 -   has  single  channel  capability  with  one 

 

laser smoke detector. 

FL2012EI

 -   has  single  channel  capability  with  two 

laser smoke detectors in a common 
chamber for coincidence detection. 

FL2022EI

 -   has two channel capability with two laser 

  

smoke detectors in separate chambers, 

 

one detector per channel. 

This guide provides information for mounting and basic 
installation

 

using the 

unit’s default factory settings.   

 

 

 

SPECIFICATIONS 

Environmental Ratings

 

Temperature: 

-10

o

C to 55

o

Relative Humidity: 

10% to 93% (non-cond) 

IP Rating: 

IP65 

Mechanical: 

Exterior Dimensions: 

403 x 356 x 135mm 

Wiring: 

0.5mm

2

 to 2.0mm

2

 max 

Maximum Single Pipe Length:  100m  
 

(Classes A, B & C) 

Maximum Number of Holes: 

See Table 1A 

Pipe Spec (EN54-20 Compliance): to EN61386 
                                        (Crush 1, Impact 1, Temp 31) 
Outside Pipe Diameter: 

25mm or 27mm (nom.) 

Shipping Weight: 

 

6.5kg (incl. detectors) 

 
 
 
 

Colour Code Key:

 (refer to back page) 

 

Black: 

applies to both FL01nn and FL20nn Series 

 

Blue: 

refers to Important Settings which should be 
verified

 

 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Figure 1: Dimensions and Knock-Outs 

PARTS LIST 
Description 

Quantity 

FAAST LT Unit 

Mounting Bracket 

3-pin Terminal Block 

4-pin Terminal Block 

2-pin Terminal Block 

47K

Ω EOL Resistor 

USB Cable 

Front Panel Labelling Pack 

USB Memory Stick with documents 

FAAST Carton Contents Guide 

Important Note 

Aspirating  Smoke  Detectors  supplied  and  installed 
within  the

 

EU  must  conform  to  the  EU  Construction 

Products  Directive  (89/106/EEC)  and  the  related 
European  Product  Standard  EN  54-20. FAAST  LT  has 
been  tested  and  certified  to  ensure  that  it

 

conforms  to 

the  necessary  Standards,  but  strict  adherence  to  this

 

i

nstruction  guide  is  advised  to  ensure  that  the 

installation  meets

 

the  requirements  of  the  CPD 

Directive. 

Electrical Characteristics 

Voltage Range:  18.5 - 31.5 V

DC

, Nominal =

 

24V

DC

 

Supply Current:  @ 24V

DC

, 25

o

C - excludes Sounders 

1 Channel:   170mA (typ), 360mA (max) 
2 Channel:   270mA (typ), 570mA (max)

 

Fan Speeds: 

Min = 1 

Typ = 5 

Max=10 

Panel Loop:  

Supply Voltage: 

15-29V

DC

 (Loop Current 

900mA) 

Standby Current: 

900µA @ 24V

DC

 (max). Poll every 5s 

Module Isolator Characteristics: 

Maximum Rated Switching Current (under short circuit) 

 

Is max: 

0.9A@

29V 

Maximum  Leakage  Current  with  switch  open  (isolated  state) 

IL max : 

15mA 

Maximum series impedance with the switch closed : 
 

(Zmax): 

190mΩ @ 15V

DC

; 1A 

Power Reset:  

0.5sec 

Configurable Input-Activation Time:  2sec (minimum) 
Relay Contact Ratings: 

 2.0A@30V

DC 

 

0.5A@30V

AC

Содержание SYSTEM SENSOR FAAST LT Series























Отзывы: