Pertronic SYSTEM SENSOR FAAST LT Series Скачать руководство пользователя страница 12

Страница: 12 / 22

FAAST LT Loop-Based Installation & Maintenance Guide Iss 1.0, 201701

Channels and Sensors:

To configure the device, set the parameters in the

Channels and Sensors

tab.

a) Select

Configuration

on the left pane.

b) Click the device. The General parameters configuration screen appears in the right pane.
c) Select the

Channels and Sensors

tab.

Specify the following details.

Fields

Description

Channels:

Enable the required

Channel

(s). The options are:



Channel 1



Channel 2

Note:

The following fields are configured based on the specific

Channel

which is selected

Label:

Specify a label to identify the zones served by the channels

Alarm is Latched

Select either of the following:



Yes

: The device retains the Alarm relay activated state until a Reset is performed



: The device automatically de-activates the relay

Fan Speed Mode:

Select either of the following:



Auto

: the device automatically sets the fan speed, at every power ON, to reach the

configured reference flow



Manual

: the device uses the configured manual speed.

Fan Speed:

Drag and set the speed scale for the fan

Note:

The fan speed set here is considered for the calculations of the built network when the
fan speed mode is selected as

Manual

Reference Flow:

Specify the flow value in litre per minute (l/min)

Filter Due Date:

Specify the due date for the air filters. The device displays a filter fault after the due date

Sensors:

The Sensor Enabled state is based on the

Channel Enabled

state:



Sensor 1 enabled



Sensor 2 enabled

Note:

either of the two

Sensors

may be disabled if the device has one channel and two

sensors

Sensor blinking
replicated:

Select either of the following.



Yes

: The channel alarm LED blinks a steady green when the sensor is polled



: The channel alarm LED does not blink when the sensor is polled

Common
chamber:

Select either of the following.



Yes

: Alarm is set when one sensor is in the Alarm condition



: Alarm is set when both the sensors are in the Alarm condition

d) Save to implement the changes.

To configure the

Advanced

parameters, refer to Advanced Configurable Parameters

Содержание SYSTEM SENSOR FAAST LT Series























Результаты поиска

Содержание SYSTEM SENSOR FAAST LT Series

Отзывы:

Бренды по названию

Популярные бренды

Pertronic SYSTEM SENSOR FAAST LT Series, Руководство по установке и обслуживанию

Результаты поиска

Содержание SYSTEM SENSOR FAAST LT Series

Отзывы:

Бренды по названию

Популярные бренды