Pertronic SYSTEM SENSOR FAAST LT Series Скачать руководство пользователя | Manualshive

Страница: 9 / 22

background image

© Pertronic Industries Ltd

9

FAAST LT Loop-Based Installation & Maintenance Guide Iss 1.0, 201701

2

FOAM GASKET

3

1

FILTER

1

2

3

SERVICE:

WARNING

Isolate the Aspirating Detector from the Fire Alarm system to prevent

any unwanted Alarms when opening the

front door of the unit.

Make sure all power is removed from the system before removing

any covers.

Service Mode:

The device enters SERVICE Mode if the cabinet door is opened during Normal operation. The FILTER LEDs
blink, the unit switches off the power to the fans and stops communicating with the Fire Panel - the Laser smoke
detectors continue to communicate with the panel.

When the cabinet door is closed, the unit restarts automatically.

Filters:

Periodic cleaning or replacement of the filters is required.
The filters are located inside the cabinet at the top of the unit (see Figure 10 displayed on Page 4) and are
removed as shown in the following sequence:

Either replace the filter assembly or carefully brush off the accumulated dust.
Note: if replacing the filter, remove the foam gasket from the old

filter and place onto the new filter. When placing

the new filter into

the slot, ensure that the gasket is correctly aligned.

Refit the filter, close and secure the cabinet door. The unit will initialise and restart.

Laser Smoke Detectors:

The smoke detectors are located under the sensor cover (see Figure 10 displayed on Page 4). To access the
detectors, follow the

sequence below:

If replacing a detector, ensure that the address set on the new

detector is the same as on the detector being

replaced.

LASER SAFETY INFORMATION:

The detector contains a Class 1 laser product. Radiation emitted

inside the smoke sensor is

completely contained within its housings

and protective covers during all phases of operation.

«
...
7
8
9
10
11
...
»

Содержание SYSTEM SENSOR FAAST LT Series























Отзывы:

Нет отзывов

Похожие инструкции для SYSTEM SENSOR FAAST LT Series

Бренд: Teknim Страницы: 8

Бренд: Zeta Страницы: 2

Бренд: UniPOS Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды