Pertronic SYSTEM SENSOR FAAST LT Series Скачать руководство пользователя | Manualshive

Страница: 4 / 22

background image

© Pertronic Industries Ltd

4

FAAST LT Loop-Based Installation & Maintenance Guide Iss 1.0, 201701

1 2 3 4 5 6 7 8 9 10 1112 131415161718

1

2

3

4

5

6

SAMPLING AREA

SAMPLING AREA

CHANNEL 2 FILTER

POWER AND
ALARM
CONNECTIONS

CHANNEL 1 FILTER

USB PORT

SENSOR COVER

POSITION FOR TEST MAGNET

POSITION FOR TEST MAGNET

EARTH BAR
MOUNT

EARTH BAR
MOUNT

EARTH BAR
(OPTIONAL)

Pipe Installation

Figure 9: Pipe Installation

Wiring Installation

Power, Alarm and Control Connections

Figure 10: Inside the Detector

Exhaust Pipe

Notes: a) All wiring should comply with

local requirements and regulations.

b) Loop wiring must observe the
recommendations of the panel
manufacturer

Notes:

- use the PipeIQ BOM Report to order the Pipe components

required to assemble the system

- use the PipeIQ Pipe Layout Report to assemble the pipe layout

Important: follow the Pipe Layout report as closely as practical.

- ensure Pipe Lengths are correct
- ensure Sampling Point holes are drilled at the stated positions

-

ensure Sampling Point Hole Size is as defined

The PipeIQ design is based upon the information provided to the designer - this is often incomplete and therefore
inaccurate.
If it is not practical to install the system as designed, stop work, record the issues taking care to measure the
changes required, then redesign the PipeIQ BEFORE proceeding

(Unequal Pressures)

(Equal Pressures)

«
...
2
3
4
5
6
...
»

Содержание SYSTEM SENSOR FAAST LT Series























Отзывы:

Нет отзывов

Похожие инструкции для SYSTEM SENSOR FAAST LT Series

Бренд: Tyco Страницы: 162

Бренд: Fire-Lite Alarms Страницы: 64

Бренд: United Technologies Страницы: 8

Бренд: Z-Wave Страницы: 7

FireClass FC700 Series

Бренд: Johnson Controls Страницы: 49

Бренд: GFS Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды