Perkins WK 1300 Series EDi Скачать руководство пользователя страница 34 | Manualshive

Страница: 34 / 40

Perkins WK 1300 Series EDi Скачать руководство пользователя страница 34

5

30

User’s Handbook, TPD 1352E, issue 4

1300 Series EDi Models WK to WS

Lubricating oil specification

The specification of lubricating oil that is recommended for these engines are API CI-4 or DHD-1.

This specification of lubricating oil will provide the necessary protection for your engine. A higher specification
of lubricating oil is acceptable.

Caution: The type of lubricating oil to be used may be affected by the quality of the fuel which is available. For
further details see "Fuel specification" on page 29.

Always ensure that the correct viscosity grade of lubricating oil is used for the ambient temperature range in
which the engine will run as shown in the chart (A).

Note:

The shaded areas in the chart (A) indicate the preferred viscosity grade of oil for the temperature range.

Increase in oil consumption may be expected when SAE 0W-30, 5W-30 and 10W-30 oils are used.
Check oil levels more frequently.

A

0W-30

5W-30

10W-30

15W-40

-30

-20

-10

0

10

20

30

40

50

o

o

C

-22

-4

14

32

50

68

86

104

122 F

«
...
32
33
34
35
36
...
»

Содержание WK 1300 Series EDi









































Отзывы:

Нет отзывов