Perkins WK 1300 Series EDi Скачать руководство пользователя страница 32 | Manualshive

Страница: 32 / 40

Perkins WK 1300 Series EDi Скачать руководство пользователя страница 32

4

28

User’s Handbook, TPD 1352E, issue 4

1300 Series EDi Models WK to WS

How to set the valve tip clearances

The valve tip clearance is checked with feeler gauges between the top of the valve stem and the rocker lever
(B), with the engine cold. The correct clearance for the inlet valves and the exhaust valves is 0,64 mm
(0.025 in). The valve positions are shown at (A).

The arrangement of the valves for each cylinder in sequence is inlet valve then exhaust valve.

Note:

Number 1 cylinder is at the front of the engine.

1

Disconnect the air inlet pipe at the rocker cover/induction manifold.

2

Release the 13 cap screws which retain the rocker cover and remove the cover.

3

Turn the crankshaft in the normal direction of rotation until valve 11 (A) has just opened and valve 12 has

not closed fully. Check/adjust the clearances of valves 1 and 2.

4

Set valves 3 and 4 as indicated above then check/adjust the clearances of valves 9 and 10.

5

Set valves 7 and 8 then check/adjust the clearances of valves 5 and 6.

6

Set valves 1 and 2 then check/adjust the clearances of valves 11 and 12.

7

Set valves 9 and 10 then check/adjust the clearances of valves 3 and 4.

8

Set valves 5 and 6 then check/adjust the clearances of valves 7 and 8.

9

If necessary, put a new rocker cover/induction manifold gasket in position on the cylinder head. Align

carefully the cover and the gasket. Fit the cap screws which retain the rocker cover and tighten them to 17 Nm
(13 lbf ft) 1,7 kgf m.

10

Connect the air inlet pipe to the rocker cover

W202/1

B

A

W014

1 2

3 4

5 6

7 8

9 1

0 1

1 1

2

«
...
30
31
32
33
34
...
»

Содержание WK 1300 Series EDi









































Отзывы:

Нет отзывов