manualshive.com logo in svg

Perkins 402F-05, Руководство по эксплуатации и обслуживанию, Страница: 75 / 88

Поделиться
Скачать
Perkins 402F-05 Скачать руководство пользователя страница 75

Illustration 46

g03381282

Typical example

1.

Install a new filter element (2) to the fuel filter base

(1).

2.

Lubricate the O ring seal (3) with clean engine oil.

Do NOT fill the bowl with fuel before the assembly
is installed.

3.

Install the filter bowl (4) to the fuel filter base (1).

Tighten the filter bowl (4) by hand.

4.

The secondary fuel filter must be replaced at the

same time as the primary fuel filter. Refer to the
Operation and Maintenance Manual, “Fuel System
Secondary Filter - Replace”.

i02627223

Fuel System Primary Filter/
Water Separator - Drain

 

Fuel leaked or spilled onto hot surfaces or electri-
cal components can cause a fire. To help prevent
possible injury, turn the start switch off when
changing fuel filters or water separator elements.
Clean up fuel spills immediately.

NOTICE

The water separator is not a filter. The water separa-
tor separates water from the fuel. The engine should
never be allowed to run with the water separator more
than half full. Engine damage may result.

Illustration 47

g01316965

Typical example

1.

Open drain (1). Catch the draining fluid in a

suitable container. Dispose of the drained fluid
correctly.

2.

Close drain (1).

NOTICE

The water separator is under suction during normal
engine operation. Ensure that the drain valve is tight-
ened securely to help prevent air from entering the
fuel system.

SEBU9064

75

Maintenance Recommendations

Fuel System Primary Filter/Water Separator - Drain

Содержание 402F-05

























































































Отзывы:

Нет отзывов