Perkins 402F-05 Скачать руководство пользователя страница 51 | Manualshive

Страница: 51 / 88

Perkins 402F-05 Скачать руководство пользователя страница 51

Maintenance
Recommendations

i04056177

System Pressure Release

Coolant System

Pressurized system: Hot coolant can cause seri-
ous burn. To open cap, stop engine, wait until ra-
diator is cool. Then loosen cap slowly to relieve
the pressure.

Ensure that the power supply is isolated before any
service or repair is performed.

To relieve the pressure from the coolant system, turn
off the engine. Allow the cooling system pressure cap
to cool. Remove the cooling system pressure cap
slowly in order to relieve pressure.

Fuel System

To relieve the pressure from the fuel system, turn off
the engine.

Engine Oil

To relieve pressure from the lubricating system, turn
off the engine.

i05341018

Welding on Engines with
Electronic Controls

Correct welding procedures are necessary in order to
avoid damage to the following components:

• Electronic Control Module (ECM) on the engine

• Clean Emissions Module (CEM)

• Sensors

• Associated components

Components for the driven equipment should also be
considered. When possible, remove the component
that requires welding. When welding on an engine
that is equipped with an ECM and removal of the
component is not possible, the following procedure
must be followed. This procedure minimizes the risk
to the electronic components.

1.

Stop the engine. Remove the electrical power from

the ECM.

2.

Ensure that the fuel supply to the engine is turned

off.

3.

Disconnect the negative battery cable from the

battery. If a battery disconnect switch is installed,
open the switch.

4.

Disconnect all electronic components from the

wiring harnesses. Include the following
components:

• Electronic components for the driven equipment

• ECM

• Sensors

• Relays

NOTICE

Do not use electrical components (ECM or ECM sen-
sors) or electronic component grounding points for
grounding the welder.

SEBU9064

51

Maintenance Recommendations

System Pressure Release

«
...
49
50
51
52
53
...
»

Содержание 402F-05

























































































Отзывы:

Нет отзывов