Perkins 402F-05 Скачать руководство пользователя страница 56

Страница: 56 / 88

Move the alternator in order to increase or

decrease the belt tension.

Tighten adjusting bolt (1) and tighten mounting

bolts and nut (2). Tighten bolt (3). Tighten all fixing
to a torque of 25 N·m (221 lb in)

i05341723

Alternator and Fan Belts -
Replace

For applications that require multiple drive belts,
replace the belts in matched sets. Replacing only one
belt of a matched set will cause the new belt to carry
more load because the older belt is stretched. The

additional load on the new belt could cause the new

belt to break.

Note:

When new belts are installed, check the belt

tension again after 20 hours of engine operation.

Removal and Installation Procedure

Refer to the original equipment manufacture for
removal and installation of the fan guards.

Illustration 27

g03383665

Typical example

Illustration 28

g03383666

Typical example

Loosen adjusting bolt (1) and mounting bolt and

nut (2). Loosen bolt (3).

Push the alternator (4) towards the engine.

Note:

If the belt is to be reused, mark the belt in order

to show direction of rotation.

Illustration 29

g03383667

Typical example

Remove the belt (5).

SEBU9064

Maintenance Recommendations
Alternator and Fan Belts - Replace

Содержание 402F-05
























































































Результаты поиска

Содержание 402F-05

Отзывы:

Perkins 402F-05, Руководство по эксплуатации и обслуживанию, Страница: 56 / 88

Результаты поиска

Содержание 402F-05

Отзывы: