Perkins 402F-05 Скачать руководство пользователя страница 68

Страница: 68 / 88

i05335963

Engine Crankcase Breather -
Replace

NOTICE

Keep all parts clean from contaminants.

Contaminants may cause rapid wear and shortened
component life.

Illustration 39

g03380583

Typical example

(1) Screws for the breather cover
(2) Breather cover
(3) Spring
(4) Diaphragm and plate
(5) Cavity
(6) Vent hole

Loosen the screws (1) and remove the breather

cover (2) from the valve mechanism cover.

Remove the spring (3). Remove the diaphragm

and plate (4).

Clean the vent hole (6) and the cavity (5) in the

valve mechanism cover.

NOTICE

Make sure that the components of the breather as-
sembly are installed correctly. Engine damage may
occur if the breather assembly is not working
correctly.

Install a new diaphragm and plate (4) for the

breather assembly into the cavity (5) of the valve
mechanism cover.

Install a new spring (3).

Install the breather cover (2) and the four screws

(1). Tighten the screws.

i02323089

Engine Mounts - Inspect

Note:

The engine mounts may not have been

supplied by Perkins . Refer to the OEM information
for further information on the engine mounts and the
correct bolt torque.

Inspect the engine mounts for deterioration and for
correct bolt torque. Engine vibration can be caused
by the following conditions:

• Incorrect mounting of the engine

• Deterioration of the engine mounts

• Loose engine mounts

Any engine mount that shows deterioration should be
replaced. Refer to the OEM information for the
recommended torques.

i05164949

Engine Oil Level - Check

Hot oil and hot components can cause personal
injury. Do not allow hot oil or hot components to
contact the skin.

SEBU9064

Maintenance Recommendations
Engine Crankcase Breather - Replace

Содержание 402F-05
























































































Результаты поиска

Содержание 402F-05

Отзывы:

Perkins 402F-05, Руководство по эксплуатации и обслуживанию, Страница: 68 / 88

Результаты поиска

Содержание 402F-05

Отзывы: