Perkins 1106C Genset Скачать руководство пользователя страница 90

Страница: 90 / 188

KENR6933

Troubleshooting Section

i02527037

CID 0253 FMI 02

Conditions Which Generate This Code:

The Electronic Control Module (ECM) detects

incorrect engine software.

System Response:

If equipped, the warning light will come on.

This diagnostic code is not logged.

Factory passwords are required to clear this

diagnostic code.

Possible Performance Effect:

The engine will not start.

Troubleshooting:

The

ash

le in the ECM is from the wrong engine

family.

Use the electronic service tool to install the correct

ash

le into the ECM. Refer to the Troubleshooting

Guide, “Flash Programming”.

Perform the following diagnostic procedure: “None”

Results:

•

OK – STOP.

i02527038

CID 0261 FMI 11

Conditions Which Generate This Code:

The Electronic Control Module (ECM) detects the

following conditions:

•

The primary speed/timing sensor and the

secondary speed/timing sensor are off by more

than 8 crankshaft degrees.

•

The engine has been running for more than

seconds.

•

Diagnostic code 0190-08 is not active.

•

No 0041 diagnostic codes are active.

System Response:

This code will not be logged. If equipped, the warning

light will be on when this code is active.

Possible Performance Effect:

The pressure in the fuel rail may be unstable and the

engine may not run smoothly.

Troubleshooting:

Check the timing of the fuel rail pump. Refer to

Disassembly and Assembly, “Fuel Injection Pump

- Install”.

Results:

•

OK – STOP.

i02655638

CID 0262 FMI 03

Conditions Which Generate This Code:

The Electronic Control Module (ECM) detects the

following conditions:

•

The 5 Volt supply is greater than 5.16 Volts DC for

more than one second.

•

The ECM has been powered for at least three

seconds.

•

Diagnostic code 0168-01 is not active.

System Response:

The ECM sets all of the pressure sensors and

temperature sensors to the default values.

The ECM will derate the engine.

Possible Performance Effect:

The engine will be derated.

Troubleshooting:

Perform the following diagnostic procedure: “5 Volt

Sensor Supply Circuit - Test”

Results:

•

OK – STOP.

Содержание 1106C Genset




























































































































































































Результаты поиска

Содержание 1106C Genset

Отзывы:

Perkins 1106C Genset, Руководство по устранению неисправностей, Страница: 90 / 188

Результаты поиска

Содержание 1106C Genset

Отзывы: