Perkins 1106C Genset Скачать руководство пользователя страница 58

Страница: 58 / 188

KENR6933

Troubleshooting Section

Recommended Actions

Diagnostic Codes

Use the electronic service tool to check for any

diagnostic codes that may be related to high fuel

consumption.

Misreading of Fuel Level

Monitor the fuel consumption over a period of 50

engine hours. If the fuel consumption is excessive,

perform the following procedure.

Fuel Quality

The quality of the fuel that is used in the engine

will affect the rate of fuel consumption. Refer to

“General Fuel Information” in the Operation and

Maintenance Manual, “Re

ll Capacities”.

If the fuel is not of an acceptable quality, drain

the fuel system and replace the fuel

lters. Re

the fuel system with fuel of an acceptable quality.

Refer to the applicable sections in the Operation

and Maintenance Manual.

If the fuel is of an acceptable quality, refer to

“Quality of Oil”.

Quality of Oil

The nominal viscosity of the lubricating oil that

is used in the engine will affect the rate of fuel

consumption. The viscosity of lubricating oil is

ned by the SAE grade of the lubricating oil.

The grade of the lubricating oil must be correct

for the ambient conditions. Lubricating oil that is

intended for use in high ambient temperatures

will have a negative effect upon the rate of fuel

consumption in cold ambient temperatures. Refer

to “Engine Oil” in the Operation and Maintenance

Manual, “Re

ll Capacities”.

The actual viscosity of the lubricating oil that is

used in the engine will change throughout the

service life of the oil. Lubricating oil that is heavily

contaminated will have a negative effect upon the

rate of fuel consumption.

If the oil is not of an acceptable quality or if the

oil has exceeded the service life, drain the oil

system and replace the oil

lters. Re

ll the oil

system with oil of an acceptable quality. Refer

to the applicable sections in the Operation and

Maintenance Manual.

If the oil is of an acceptable quality, refer to

“Operation in Cold Conditions”.

Low Engine Temperature

The operating temperature of the engine will affect

the rate of fuel consumption. Operation of the

engine below the correct temperature will increase

fuel consumption. Failure of the water temperature

regulator can prevent the engine from operating at

the correct temperature.

If the engine operating temperature is low, check

the operation of the water temperature regulator. If

the water temperature regulator does not operate

correctly, a new water temperature regulator must

be installed. Refer to Disassembly and Assembly,

“Water Temperature Regulator - Remove and

Install”.

Prolonged Operation at Idle Speed

Prolonged operation of the engine at idle speed

increases fuel consumption.

When the engine is operated at idle speed, the fuel

that is consumed provides no useful work. Prolonged

operation at idle speed will cause a measurable

deterioration in the overall fuel consumption of the

engine.

Operation of the engine for long periods at idle

speed will cause a deterioration of the internal

components of the engine. A deterioration of the

internal components of the engine will increase fuel

consumption.

Engine Operating Speed

The operating speed of the engine will affect the rate

of fuel consumption.

High engine speed will increase fuel consumption.

At high engine speeds, internal power losses in

the engine increase and more power is required to

drive the alternator and the fan. These power losses

increase fuel consumption.

Lugging down the engine to a low engine speed will

increase fuel consumption. At low engine speeds, the

combustion ef

ciency of the engine is reduced. This

will require more fuel to be used.

Air Inlet and Exhaust System

Leakage of gas or an increased restriction in either

the air intake or the exhaust system can reduce

the

ow of combustion gas through the engine. A

change in the

ow of combustion air into the engine

adversely affects combustion ef

ciency and the rate

of fuel consumption.

Содержание 1106C Genset




























































































































































































Результаты поиска

Содержание 1106C Genset

Отзывы:

Perkins 1106C Genset, Руководство по устранению неисправностей, Страница: 58 / 188

Результаты поиска

Содержание 1106C Genset

Отзывы: