Perkins 1106C Genset Скачать руководство пользователя страница 170

Страница: 170 / 188

170

KENR6933

Troubleshooting Section

Test Step 1. Check for Connector

Damage.

Turn the keyswitch to the OFF position.

Check the connectors and the harness for the

following faults: damage, abrasion, corrosion, and

incorrect attachment.

Refer to Troubleshooting, “Electrical Connectors

- Inspect”.

Perform a 45 N (10 lb) pull test on each of the

wires in the harness that are associated with the

speed demand device. Check the wire connectors

at the ECM and at the control system. The wire

connectors are shown in table 40.

Check the screw for the ECM connector for the

correct torque of 5.0 N·m (44 lb in).

Expected Result:

The connectors and the harness should be free of

the following faults: damage, abrasion, corrosion,

and incorrect attachment.

Results:

•

–

Proceed to Test Step 2.

•

Not OK

Repair:

Repair the connectors or the harness

and/or replace the connectors or the harness.

Verify that the repair eliminates the fault.

STOP.

Test Step 2. Check for active Diagnostic

Codes.

Turn the keyswitch to the ON position.

Use the Perkins EST to check for diagnostic

codes.

Expected Result:

RESULT 1

The Perkins EST displays the following

active diagnostic codes or recently logged diagnostic

codes:

•

91-03

•

91-04

RESULT 2

The Perkins EST displays no active

diagnostic codes:

Results:

•

Result 1

–

Proceed to Test Step 3.

•

Result 2 – There may be an intermittent connection

in the wiring. Proceed to Test Step 3.

Test Step 3. Check the Control Signal.

Refer to the OEM supplied manual for the control

system.

Check that the output signal from the control

system is correct.

Expected Result:

The output signal from the control system should be

within the speci

cation in the OEM supplied manual.

Results:

•

–

The output signal from the control system is

correct. Proceed to Test Step 4.

•

Not OK – The output signal from the control

system is not correct or the control system is

incorrectly con

gured.

Repair:

Repair the control system or con

gure the

control system. Refer to the OEM supplied manual.

Verify that the repair eliminates the fault.

STOP.

Test Step 4. Check the Signal at the ECM.

Turn the keyswitch to the OFF position.

Remove the P1 OEM connector.

Temporarily remove the pin from P1:54.

Reconnect P1 OEM connector.

Connect the red probe of a multimeter to the

removed pin and the black probe of a multimeter

to P1:33.

Turn the keyswitch to the ON position.

Check that the signal at the ECM is the same

value as the output signal from the control system.

Turn the keyswitch to the OFF position.

Remove P1 OEM connector and reinstall P1:54 to

the P1 OEM connector.

Reconnect P1 OEM connector.

Содержание 1106C Genset




























































































































































































Результаты поиска

Содержание 1106C Genset

Отзывы:

Perkins 1106C Genset, Руководство по устранению неисправностей, Страница: 170 / 188

Результаты поиска

Содержание 1106C Genset

Отзывы: