Perkins 1106C Genset Скачать руководство пользователя страница 85

Страница: 85 / 188

KENR6933

Troubleshooting Section

Troubleshooting:

This diagnostic code can be caused by an open

circuit or a short to another power source.

Perform the following diagnostic procedure: “Engine

Pressure Sensor Open or Short Circuit - Test”

Results:

•

OK – STOP.

i02655615

CID 0100 FMI 04

Conditions Which Generate This Code:

The Electronic Control Module (ECM) detects the

following conditions:

•

The signal voltage from the engine oil pressure

sensor is less than 0.1 Volts DC for more than

eight seconds.

•

The ECM has been powered for at least two

seconds.

•

The engine is running.

System Response:

The ECM will log the diagnostic code. If equipped,

the warning lamp will come on. The ECM will set

data for engine oil pressure to the default value. The

electronic service tool will display “Voltage Below

Normal” on the status screens.

Possible Performance Effect:

None

Troubleshooting:

This code can be caused by a short to ground or a

shorted sensor.

Perform the following diagnostic procedure: “Engine

Pressure Sensor Open or Short Circuit - Test”

Results:

•

OK – STOP.

i02655616

CID 0100 FMI 10

Conditions Which Generate This Code:

The Electronic Control Module (ECM) detects the

following conditions:

•

No other codes for the oil pressure sensor are

active.

•

No 0262 diagnostic codes are active for the 5 Volt

supply.

•

The engine speed is greater than 600 rpm.

•

The engine oil pressure signal is within the limits of

410 kPa (59 psi) to 520 kPa (75 psi) with a pressure

variation of less than 1.68 kPa (0.25 psi)for more

than 30 seconds.

•

The engine oil pressure signal remains constant

for 30 seconds.

System Response:

If equipped, the warning lamp will be on.

The ECM will log the diagnostic code. The diagnostic

code can be viewed on the electronic service tool.

The ECM will

ag the engine oil pressure as invalid

data.

The data for engine oil pressure is set to a default

value of 500 kPa (72 psi).

The electronic service tool will display “Conditions

Not Met” on the status screen.

Possible Performance Effect:

None

Troubleshooting:

This diagnostic code is designed to detect the loss

of the 5 Volt supply to the sensor.

Perform the following diagnostic procedure: “Engine

Pressure Sensor Open or Short Circuit - Test”

Results:

•

OK – STOP.

Содержание 1106C Genset




























































































































































































Результаты поиска

Содержание 1106C Genset

Отзывы:

Perkins 1106C Genset, Руководство по устранению неисправностей, Страница: 85 / 188

Результаты поиска

Содержание 1106C Genset

Отзывы: