PerkinElmer Spotlight 400 Series Скачать руководство пользователя страница 34

Страница: 34 / 120

34 . Spotlight 400 Series User’s Guide

Viewing in Reflectance/Diffuse Reflectance

When the imager is in viewing mode in reflectance or diffuse reflectance (Figure 11):

•

The reflectance illuminator assembly directs light from the upper LED down through one

side of the cassegrain onto the sample.

•

The upper cassegrain collects the reflected light from the sample and sends it upward

through the aperture.

The lower ‘transmission’ illuminator is also active in reflectance and diffuse reflectance

modes, giving simultaneous illumination from above and below.

Figure 11 Path of the visible beam for viewing a sample in reflectance/diffuse

reflectance

Mirror pair

Visible focus lens

assembly

Variable aperture

Reflectance

illuminator assembly

Upper cassegrain

Sample position

Lower cassegrain

Lower dichroic

mirror

Detector

Camera

Содержание Spotlight 400 Series

























































































































Результаты поиска

Содержание Spotlight 400 Series

Отзывы:

Похожие инструкции для Spotlight 400 Series

Бренды по названию

Популярные бренды

PerkinElmer Spotlight 400 Series, Руководство пользователя

Результаты поиска

Содержание Spotlight 400 Series

Отзывы:

Похожие инструкции для Spotlight 400 Series

Бренды по названию

Популярные бренды