PerkinElmer Spotlight 400 Series Скачать руководство пользователя страница 111

Страница: 111 / 120

Appendices . 111

Click

Next

The Calibration Data page is displayed.

NOTE: For a new SpectrumIMAGE installation, the

Existing PelImage.ini file in

C:\Windows\

option is not present.

For a new SpectrumIMAGE installation, select

Calibration media (recommended)

If you are upgrading from an earlier version of SpectrumIMAGE, select

Existing

PelImage.ini file in C:\Windows\

CAUTION

Do not select

Default calibration settings (not generally recommended)

This option is only for PerkinElmer Service Engineers.

For a new installation, the default calibration settings do not include the

factory settings for your Spotlight system that are supplied on its Calibration

data disk.

If you are upgrading from an earlier version of SpectrumIMAGE, the default

calibration settings include neither the factory settings for your Spotlight

system, nor any settings that have been customized since the system was

installed.

Содержание Spotlight 400 Series

























































































































Результаты поиска

Содержание Spotlight 400 Series

Отзывы:

Похожие инструкции для Spotlight 400 Series

Бренды по названию

Популярные бренды

PerkinElmer Spotlight 400 Series, Руководство пользователя

Результаты поиска

Содержание Spotlight 400 Series

Отзывы:

Похожие инструкции для Spotlight 400 Series

Бренды по названию

Популярные бренды