PerkinElmer Spotlight 400 Series Скачать руководство пользователя страница 97

Страница: 97 / 120

Maintenance . 97

Inspecting the Imager

At least once a year, or whenever the imager has been subjected to adverse environmental

conditions, visually inspect the housing to make sure that no covers are loose or distorted.

At the same time, make sure that all required labels are firmly in place (see Figures 2–5 on

pages 19–20).

Protecting the Imager

The most important rule in caring for the imager is to keep it as free from dust and dirt as

possible. Dust, fingerprints, and smears on the optics reduce the quality of the images it

produces.

Whenever the imager is not in use, cover it with its plastic cover.

CAUTION

Ensure the power is switched off when the imager is covered.

Cleaning the Optics

The imager was aligned, cleaned, and sealed at the factory. Do not attempt to take it apart.

CAUTION

Avoid the excessive use of solvents. Flowing solvents dissolve the cement

on cemented optics; dissolved cement can damage mirror surfaces.

Cleaning the Cover

CAUTION

Ensure the power is switched off and the supply lead is disconnected

before cleaning the cover.

You can clean the outside of the imager or stage controller using a damp cloth. Mild

detergent may be used, if necessary. Always perform a patch test on an inconspicuous area

before you clean the entire instrument.

Avoid spilling liquid into the imager or stage controller. Clean all external spills immediately.

If anything that is spilled enters the main body of any part of the system, switch off the

power and call a PerkinElmer Service Engineer.

Содержание Spotlight 400 Series

























































































































Результаты поиска

Содержание Spotlight 400 Series

Отзывы:

Похожие инструкции для Spotlight 400 Series

Бренды по названию

Популярные бренды

PerkinElmer Spotlight 400 Series, Руководство пользователя

Результаты поиска

Содержание Spotlight 400 Series

Отзывы:

Похожие инструкции для Spotlight 400 Series

Бренды по названию

Популярные бренды